Fghs2631pf Parts

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This ice cream shelf rail guides and secures the freezer's ice cream shelf so tubs stay level and accessible. It restores proper shelf alignment and prevents sliding or rattling of the ice cream compartment shelf. What it does:

• Holds the ice cream shelf in place so frozen goods stay stable during door movement
• Guides shelf slides to keep the shelf aligned and prevent binding
• Reduces shelf rattling and noise from the ice cream compartment
• Helps restore proper shelf seating after a broken or worn rail

• High-level replacement; remove shelf and slide to access rail mounting points
• Use common hand tools; support shelf while loosening or tightening fasteners
• Disconnect power only if working near electrical components; exercise caution with sharp edges
• If screws or clips are missing or damaged, replace them before final reassembly

This replacement nameplate label restores the appliance's identification and rating information so you can read model, serial, and electrical data clearly. Helps when the original label is faded, damaged, or missing. What it does

• Displays model and serial numbers, electrical ratings and safety markings for identification and service
• Replaces faded, torn, or illegible factory labels so appliance data is readable
• Helps technicians and owners confirm correct specifications during repairs or replacement parts ordering
• Does not affect appliance operation; used for identification and information only

• One replacement nameplate label

• Clean and dry the surface before applying so the label adheres and lays flat
• Align carefully; many labels are adhesive-backed and are intended for single use
• Avoid placing over gaskets, vents, or moving parts; install where original label was located

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

Right hand side. For the left hand side order 241674401

This control rod bracket secures the control rod to the appliance, restoring proper linkage and part alignment for reliable operation. Designed to replace a worn or broken mounting bracket and stabilize control movement. What it does:

• Holds the control rod in place so levers and linkages operate smoothly
• Restores proper alignment when the rod is loose, bent, or detached
• Helps eliminate binding or intermittent actuator movement caused by a damaged bracket
• Supports consistent mechanical operation of the connected control components

• One control rod mounting bracket

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Remove any panels or covers as needed to access the bracket; keep fasteners organized for reassembly
• Inspect adjacent linkage and fasteners; replace any damaged clips or screws for a secure fit