Fghs2631pf Parts

This lower hinge secures and pivots a refrigerator door, restoring proper alignment and smooth opening. It helps stop door sag, uneven sealing, and rubbing that can cause cold loss or noisy operation. What it does:

• Provides a durable pivot point for the refrigerator door to open and close smoothly
• Restores correct door alignment to improve the door seal and cooling performance
• Stops door sag, rubbing against the cabinet, and uneven gaps that can lead to air leaks
• Helps reduce noise from a misaligned or worn hinge

• Support or remove the door before replacing the hinge to avoid injury or damage
• Keep fasteners and any hinge shims or bushings; reuse only if in good condition or replace with OEM parts
• Tighten mounting screws securely and check door alignment; minor shimming may be required

This pizza shelf is a direct-replacement oven shelf designed to support pizzas and other flat bakeware for stable, even cooking. Restores a missing or damaged shelf so trays and pans sit level during use. What it does:

• Provides a flat, stable surface for baking pizzas, sheet pans, and similar items
• Replaces a warped, bent or missing pizza shelf that prevents level cooking
• Helps keep cookware centered and supported to reduce sliding or tipping
• Durable finish resists everyday oven use and helps maintain even heat exposure

• Slide shelf onto existing oven rack supports until it sits securely; no tools typically required
• Allow oven to cool before removing or installing the shelf to avoid burns
• Clean with non-abrasive cleaners; avoid harsh scrubbing that can damage the finish
• Follow your oven manufacturer's instructions for safe use and placement

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This small replacement sleeve protects and guides a moving component in the appliance to reduce wear and ensure smoother operation. It helps maintain correct alignment where parts slide or rotate, preventing metal-on-metal contact. What it does:

• Acts as a protective liner or guide for a rotating or sliding shaft or pin
• Reduces wear and friction between mating parts
• Helps stop scraping, squeaking, or uneven movement around the fitted area
• Supports proper part alignment for reliable operation

• One replacement sleeve as shown

• Replace only with the exact part number to ensure correct fit
• Inspect mating shaft/pin for wear and clean before installing the sleeve
• Apply light lubricant only if specified by the manufacturer; avoid over-lubrication
• Disconnect power and follow all safety guidelines before servicing the appliance

A single replacement screw used to fasten appliance panels and components securely. This genuine-style fastener restores proper fit and helps eliminate rattles or loose parts after service or repairs. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Restores tight, stable mounting to stop rattling or vibration
• Replaces missing or stripped hardware so parts align correctly
• Works where the original appliance screw was used

• Use matching driver and apply moderate torque to avoid stripping the head or threads
• Disconnect power or unplug the appliance when accessing internal areas
• If screw threads are damaged, replace with an identical part rather than forcing

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly