Fgm0205kfcy Parts

This Tube Assembly routes water inside the refrigerator to the dispenser and ice-maker, restoring proper water flow and preventing leaks when the original line is damaged. Reliable replacement for delivery and fill connections. What it does:

• Transports water from the inlet to the ice maker/dispenser assembly
• Replaces cracked, kinked, or leaking tubing that causes puddles or low water flow
• Helps restore normal ice production and dispenser operation when the tube is the fault
• Matches OEM routing and connector types for correct fit and seal

• One tube assembly as shown

• Disconnect power and shut off the water supply before starting
• Remove ice maker or access panel as needed to reach routing; follow OEM service instructions
• Inspect fittings and replace any damaged clamps or seals; avoid kinking the new tube
• After installation, turn on water, check for leaks, and run dispenser/ice cycles to confirm proper flow

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This harness assembly is the appliance wiring connector bundle that carries power and signals between controls and components, restoring proper electrical connections for normal operation. What it does:

• Routes power and control signals between the control board and key components
• Replaces damaged, burned, or loose wiring that can cause intermittent operation
• Helps resolve symptoms like unresponsive controls, failure to start, or component loss of power
• Restores factory wiring layout and connector fit for reliable connections

• Disconnect power before starting; confirm power is off at the breaker
• Compare connectors and wire colors to the old harness before removal
• Route and secure harness to avoid heat or pinch points; use existing clips/mounts

This magnetron generates the microwave energy used to heat food in countertop and over-the-range microwaves. Replace a failed magnetron when the oven powers on but does not heat or shows arcing or loud humming. What it does:

• Converts high-voltage power into microwave radiation that heats food.
• Common symptom: microwave runs but does not heat.
• Other symptoms: unusually loud humming, arcing or sparking inside the cavity, or a burning/ozone-like smell.
• Not a user-serviceable electrical component — faults often require component-level replacement.

• Disconnect power before servicing; unplug the appliance and verify power is removed.
• Discharge the high-voltage capacitor before touching high-voltage components to avoid serious shock.
• Handle carefully; avoid touching the magnetron antenna or ceramic surfaces.

This evaporator fan motor circulates cold air inside the refrigerator compartment to maintain even cooling and proper airflow. Replaces a failed or noisy fan motor to restore consistent temperature distribution. What it does:

• Spins the evaporator fan blade to move air across the evaporator coils and throughout the fresh-food compartment
• Helps prevent uneven cooling, warm spots, and excessive frost buildup when operating correctly
• Reduces or eliminates grinding, rattling, or humming caused by a worn or failing motor
• Works as part of the refrigerator's airflow system to support normal compressor and defrost operation

• One evaporator fan motor (single unit as shown)

• Disconnect power before servicing to avoid shock or injury
• Access typically requires removing interior panels; handle evaporator fins and wiring with care
• Verify fan blade clearance and secure electrical connectors before restoring power

This metal door hinge replaces a worn or damaged refrigerator door pivot to restore smooth opening and proper door alignment. It helps keep the door secure and prevents sagging, rubbing, or uneven sealing. What it does:

• Provides a stable pivot point so the refrigerator door opens and closes correctly
• Restores proper door alignment to improve sealing and cooling performance
• Stops door sagging or rubbing on the cabinet edge
• Reduces noise from a loose or worn hinge

• One hinge

• Unplug the appliance and remove food/obstructions from the door area before starting
• Support the door while removing and installing the hinge to prevent drops or damage
• Reuse original fasteners unless replacements are specified by the manufacturer
• If the door has glass or heavy components, get a second person to help for safety

A decorative trim piece that restores the finished edge and appearance of the appliance door. Replaces worn or damaged trim to improve aesthetics and help keep the door edge sealed and protected. What it does:

• Provides a finished decorative edge to the appliance door or panel
• Helps secure and align the outer door or panel for a consistent fit
• Covers gaps and hides fasteners for improved appearance
• Commonly replaced for cracked, dented, or faded trim

• One trim piece as shown

• Disconnect power to the appliance before starting any repair
• Remove door or panel fasteners as needed to access the trim; keep hardware organized
• Use gentle prying to avoid scratching adjacent surfaces; avoid forcing the trim into place

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

Control transformer that supplies the low-voltage power needed for the appliance's electronic control/console, restoring reliable operation when the original transformer fails or the display and controls lose power. What it does:

• Converts incoming line voltage to the low-voltage supply used by the control board and console.
• Keeps the display, touchpad/keys and control electronics powered and stable.
• Common symptoms of a failing transformer: unlit or blank display, unresponsive controls, intermittent operation, or control board power loss.
• Replace a visibly burned, cracked, or shorted transformer to prevent further electrical damage.

• Always disconnect power to the appliance before servicing to avoid electric shock.
• Take care with wiring: match original connector positions and secure all wire nuts/terminals.
• Inspect mounting hardware and insulation; replace any damaged fasteners or wires.

This electronic control board manages a refrigerator's core functions, translating user inputs into operation of compressors, fans and defrost systems for reliable cooling performance. Replaces a failed main control to restore normal cycle control and UI response. What it does:

• Regulates compressor, evaporator fan and defrost cycle timing to maintain proper temperatures
• Interprets console inputs and display indicators so buttons and settings respond correctly
• Can resolve symptoms such as no cooling, intermittent cooling cycles, or unresponsive controls
• Stops or starts related components when safety sensors or switches signal a fault

• Disconnect power to the appliance before starting any service
• Handle the board carefully to avoid ESD damage; use grounding precautions if available
• Some disassembly of the control console or back panel may be required; keep fasteners organized
• Verify correct part orientation and wire/plugs match before securing; test after reassembly

This adjustable leveling foot raises and stabilizes the appliance for proper alignment and even weight distribution. It restores a steady, wobble-free base so doors close correctly and the appliance sits level on uneven floors. What it does:

• Replaces a worn or damaged cabinet/console leveling foot to restore stable support
• Allows height adjustment to correct leaning or rocking on uneven surfaces
• Helps ensure doors and drawers close smoothly by keeping the appliance level
• Fits under the appliance base where a threaded/adjustable foot is required

• One adjustable leveling foot

• Turn the appliance off/unplug and empty lower compartments before accessing the foot
• Raise or support the appliance safely following manufacturer guidance before removal/installation
• Thread the foot into the mounting socket until it contacts the floor, then fine-tune the height for level

This replacement shield protects internal appliance components from heat, debris and accidental contact, helping maintain safe operation. It provides a direct-fit replacement designed to restore the original protection and component routing. What it does:

• Covers and shields electrical or mechanical parts from debris and accidental contact
• Helps direct airflow or heat away from sensitive components where applicable
• Restores the original barrier that prevents rubbing, chafing, or exposure of wiring and connectors
• Reduces risk of damage that can cause noise, shorts, or premature wear

• One replacement shield

• Disconnect power to the appliance before beginning any work
• Installation typically requires removal of outer panels; keep fasteners organized
• Use appropriate tools and protective gloves to avoid sharp edges
• Refer to the appliance service manual or OEM instructions for exact placement and fastening