Fpge3081kf Parts

This replacement control knob provides a reliable way to select settings on compatible appliances, restoring safe, tactile control after the original knob wears, cracks, or goes missing. What it does:

• Allows turning and selecting cycles, temperatures, or functions on the appliance control shaft
• Restores a secure grip and accurate setting selection when the original knob is damaged or stripped
• Addresses symptoms such as a loose, cracked, or missing knob and difficulty changing settings
• Matches the OEM fit to slide onto the control shaft for straightforward operation

• Disconnect power to the appliance before servicing any controls.
• Most knobs pull straight off the control shaft; align the replacement on the splines and push on until it seats.
• If the knob is held by a set screw, loosen the screw before removal and retighten as needed.
• Do not force the knob; verify shaft type and orientation before final installation.

This tube clamp secures small tubing and lines inside the appliance to prevent movement and reduce wear. It keeps hoses and tubes routed properly so they don't rub against sharp edges or vibrate during operation. What it does:

• Holds water, drain or refrigerant tubing in place to prevent sagging and chafing
• Reduces vibration and rattling from loose lines
• Helps prevent tubing wear that can lead to leaks or pinch damage
• Keeps hoses routed neatly for reliable appliance operation

• Disconnect power and shut off water supply before beginning any repair
• Remove any access panels needed to reach the clamp location; use caution around sharp sheet metal
• Replace only the damaged clamp with the same style and secure tubing firmly but without over-tightening
• If tubing shows damage where it was rubbing, replace or repair the tubing before reinstalling the clamp

This refrigerator door gasket seals the cabinet door to keep cold air in and help the appliance maintain proper temperature. It replaces worn, torn, or misshapen gaskets to improve cooling efficiency and reduce frost buildup. What it does

• Creates an airtight seal between the door and cabinet to prevent cold air loss.
• Helps reduce frost and ice buildup by keeping warm, humid air out of the compartment.
• Can stop symptoms like excessive run cycles, warm spots, or visible gaps around the door.
• Restores proper door closing and alignment when the original gasket is damaged or deformed.

• High-level fit: Intended as a direct-replacement gasket.
• Prep tip: Remove food and shelves near the door area, and work with the door open on a stable surface.
• Safety: Unplug the appliance or disconnect power before doing any repairs.
• If the gasket is stiff, warming it slightly can make installation easier; avoid using open flames or excessive heat.

This refrigerator door gasket creates a tight seal around the door to help maintain proper temperature and reduce energy loss. It replaces a worn or damaged seal to improve cooling consistency and prevent moisture buildup. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost, condensation, and food spoilage caused by air leaks
• Reduces compressor runtime and energy waste from a failing seal
• Restores proper door closure when the original gasket is cracked, torn, or warped

• Inspect the door and gasket channel for debris before installing; clean surfaces for best fit
• Replace gasket with door empty or items moved to avoid interference during installation
• Seat the gasket fully into the channel and allow magnetic gaskets to snap into place; heat (hair dryer) can help soften rigid gaskets for final seating if needed

This ignitor orifice assembly positions the oven burner orifice and supports proper ignition for gas ovens. Replacing a worn assembly can restore reliable burner lighting and help the oven reach and hold temperature. What it does:

• Secures and aligns the burner orifice so gas flows correctly to the ignitor/pilot
• Enables consistent ignition of the oven burner
• Helps resolve symptoms like the oven failing to light, repeated clicking without ignition, or an unstable/weak flame
• Works as a direct replacement for the oven's original orifice/ignitor mounting component

• Turn off gas supply and disconnect power before beginning any work.
• Basic hand tools are typically required; follow OEM instructions for safe removal and reinstallation.
• If you smell gas, stop immediately.

This replacement cooktop grate restores a stable surface for pots and pans so you can cook safely and evenly. It fits over the burner area to support cookware and protect the burner assembly from spills. What it does:

• Provides a stable platform for cookware to sit securely over the burner
• Helps direct heat to cookware and maintain proper burner clearance
• Shields burners from heavy spills and large debris that can interfere with ignition
• Worn, cracked or misshapen grates can cause wobbling cookware or uneven cooking

• Allow the cooktop and burners to cool completely before removing or installing the grate
• Remove old grate by lifting straight up; align new grate over the burner and set into place—no tools typically required
• For gas ranges, ensure burners and ports are clear of debris before use; for electric glass cooktops, use only grates designed for that surface

This replacement door gasket creates a tight seal around the refrigerator or freezer door to help maintain interior temperature and reduce energy loss. It restores proper door closure for better cooling and frost prevention. What it does:

• Seals the door perimeter to keep cold air in and warm air out
• Helps maintain consistent internal temperatures for food safety
• Reduces frost build-up and compressor runtime due to air leaks
• Restores proper door alignment and closing performance

• Remove old gasket and clean the door mating surface before installing the new gasket
• Start installation at a corner and work around the door to ensure an even fit
• Gasket may be warmed slightly (hot water or hair dryer on low, if needed) to improve flexibility for positioning
• Unplug or disconnect power to the appliance before beginning work