Fphs268k84 Parts

Left side.

This lower hinge secures and pivots a refrigerator door, restoring proper alignment and smooth opening. It helps stop door sag, uneven sealing, and rubbing that can cause cold loss or noisy operation. What it does:

• Provides a durable pivot point for the refrigerator door to open and close smoothly
• Restores correct door alignment to improve the door seal and cooling performance
• Stops door sag, rubbing against the cabinet, and uneven gaps that can lead to air leaks
• Helps reduce noise from a misaligned or worn hinge

• Support or remove the door before replacing the hinge to avoid injury or damage
• Keep fasteners and any hinge shims or bushings; reuse only if in good condition or replace with OEM parts
• Tighten mounting screws securely and check door alignment; minor shimming may be required

This pizza shelf is a direct-replacement oven shelf designed to support pizzas and other flat bakeware for stable, even cooking. Restores a missing or damaged shelf so trays and pans sit level during use. What it does:

• Provides a flat, stable surface for baking pizzas, sheet pans, and similar items
• Replaces a warped, bent or missing pizza shelf that prevents level cooking
• Helps keep cookware centered and supported to reduce sliding or tipping
• Durable finish resists everyday oven use and helps maintain even heat exposure

• Slide shelf onto existing oven rack supports until it sits securely; no tools typically required
• Allow oven to cool before removing or installing the shelf to avoid burns
• Clean with non-abrasive cleaners; avoid harsh scrubbing that can damage the finish
• Follow your oven manufacturer's instructions for safe use and placement

This black door stop replaces the small bumper that limits a refrigerator/freezer door's travel, protecting the cabinet and hinge from damage. It restores proper door alignment and quiets contact when the door closes. What it does:

• Acts as a physical stop to prevent the door from swinging too far and hitting the cabinet
• Cushions door closure to reduce noise and wear on the hinge
• Helps maintain correct door alignment for a tight seal
• Common symptom: door scraping, slamming, or rubbing against cabinet edge

• Basic hand tools may be required; keep fasteners and mounting surfaces clean
• Turn off or unplug the appliance before performing any repairs that require moving the door
• Handle hardware carefully to avoid damaging surrounding trim or seals

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

A single replacement screw used to fasten appliance panels and components securely. This genuine-style fastener restores proper fit and helps eliminate rattles or loose parts after service or repairs. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Restores tight, stable mounting to stop rattling or vibration
• Replaces missing or stripped hardware so parts align correctly
• Works where the original appliance screw was used

• Use matching driver and apply moderate torque to avoid stripping the head or threads
• Disconnect power or unplug the appliance when accessing internal areas
• If screw threads are damaged, replace with an identical part rather than forcing

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

This replacement ice deflector guides ice from the ice maker/dispenser into the bin or chute to reduce spills and misdirected cubes. It restores proper ice flow and helps keep the dispenser area tidy. What it does:

• Directs ice from the ice maker or dispenser chute into the ice bin
• Helps prevent ice from falling outside the bin or jamming the dispenser
• Reduces spillage and misalignment of ice cubes during dispensing
• Restores intended ice flow after a cracked, warped, or missing deflector

• Basic snap-in or screw-in replacement—inspect mounting tabs before installation
• Power off the refrigerator (or dispenser) and remove ice/ice bin before working on the deflector
• Handle part gently to avoid breaking thin plastic tabs; replace any damaged fasteners