Frs26r2a Parts

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Color: White

This rear cover replaces the damaged or missing cabinet back panel to protect internal components and restore a finished appearance. It helps keep wires and motors shielded and prevents debris from entering the appliance. What it does:

• Shields the appliance's rear components (motor, wiring, vents) from dust and physical damage
• Restores proper airflow routing and helps reduce rattling caused by loose or broken panels
• Prevents accidental contact with internal electrical components and moving parts
• Common symptom: cracked, warped, or missing rear panel; noticeable noise, drafts, or exposed wiring

• Disconnect power before starting any work
• Removal typically requires backing out screws and lifting the old panel away; keep fasteners for reuse if undamaged
• Handle edges carefully to avoid cuts; wear gloves and eye protection
• Verify panel aligns with existing screw bosses and clips; do not force into place—confirm fit before tightening

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

This front control console cover protects and finishes the appliance's user controls while giving the unit a clean, factory appearance. It restores a secure mounting surface for buttons and the control panel. What it does:

• Replaces a cracked, warped or scratched console cover that makes the control area look damaged
• Provides a stable surface for switches, knobs and touch controls to mount to
• Helps keep internal components shielded from spills, dust and debris
• Eliminates loose or rattling trim that can interfere with normal operation

• One control console cover

• Disconnect power before beginning any repair to avoid electrical shock
• Remove trim and control hardware carefully; save screws and fasteners for reassembly
• Some applications use clips and tabs—use a trim tool or gentle prying to avoid breakage
• Secure all fasteners so the cover sits flush and buttons operate properly

This tube clamp secures small tubing and lines inside the appliance to prevent movement and reduce wear. It keeps hoses and tubes routed properly so they don't rub against sharp edges or vibrate during operation. What it does:

• Holds water, drain or refrigerant tubing in place to prevent sagging and chafing
• Reduces vibration and rattling from loose lines
• Helps prevent tubing wear that can lead to leaks or pinch damage
• Keeps hoses routed neatly for reliable appliance operation

• Disconnect power and shut off water supply before beginning any repair
• Remove any access panels needed to reach the clamp location; use caution around sharp sheet metal
• Replace only the damaged clamp with the same style and secure tubing firmly but without over-tightening
• If tubing shows damage where it was rubbing, replace or repair the tubing before reinstalling the clamp

Specs: Hex head , 8 - 15a x 1.000