Frss2323as0 Parts

This replacement crisper pan sits beneath the refrigerator crisper drawer to catch spills and support stored produce, helping keep the drawer area clean and stable. Fits as the OEM service part for compatible Frigidaire units. What it does:

• Supports the crisper drawer and helps keep fruits and vegetables stable.
• Collects spills and juices to prevent them from dripping into the cabinet below.
• Restores proper drawer seating when a cracked or warped pan prevents full engagement.
• Helps maintain a cleaner, more sanitary drawer area.

• Remove stored food and slide the crisper drawer out to access the pan.
• Lift or unclip the old pan per your refrigerator's service instructions and slide the replacement into the same position.
• Handle carefully and inspect mating rails and seals; replace any damaged hardware before reassembly.
• No special tools required for most models; wear gloves if removing a cracked pan.

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This control rod spring fits the refrigerator's ice maker shutoff arm. It restores proper tension so the ice maker cycles on/off correctly and stops making ice when the bucket is full.

• Maintains tension on the ice maker control/shutoff arm for reliable on/off operation
• Helps the arm return to position so the ice maker senses a full bin and pauses production
• A weakened or missing spring may cause an overfilling ice bucket, a loose arm, or inconsistent ice production
• Replaces damaged or stretched springs that prevent the control rod from moving smoothly

• Unplug the refrigerator and shut off water to the ice maker
• Empty the ice bin and access the shutoff arm pivot
• Note the spring's orientation; install with needle-nose pliers without bending the control rod
• Restore power/water and verify smooth arm movement and proper shutoff

This door bushing kit replaces worn hinge bushings that keep refrigerator/freezer doors aligned for smooth, stable operation. Restores proper door rotation to reduce sagging, rubbing, and noisy or stiff hinges. What it does:

• Provides replacement hinge bushings that support the door on its hinge pin for correct alignment
• Helps stop door sag, scraping, and uneven gaps that let cold air escape
• Reduces hinge noise, sticking, and rough door movement
• Fits into the door hinge assembly to restore smooth pivoting action

• Always unplug the appliance or disconnect power before starting repairs
• Support the door while removing hinge pins to prevent dropping or damage
• Remove old bushings from the hinge housing and press or snap new bushings into place; reassemble hinge and confirm alignment

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This housing assembly is the outer cabinet component that supports and protects internal appliance parts, restoring structural fit and appearance. Use it to replace cracked or damaged housings that expose internal components or cause misalignment. What it does:

• Replaces the appliance's outer housing to restore proper fit and protection
• Protects internal wiring, controls, and mechanical parts from damage and debris
• Helps correct alignment issues caused by a warped or broken cabinet
• Reduces rattles and vibration when the original housing is damaged

• 1 housing assembly

• Designed to mount to the appliance frame; some trim or panels may need temporary removal
• Inspect surrounding seals, fasteners, and clips; replace any damaged hardware
• Use appropriate hand tools and disconnect power before beginning work

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

The Socket is an OEM part for Frigidaire refrigerators. It is responsible for holding and connecting the light bulb in the refrigerator, allowing for proper lighting inside the appliance.

A bad light socket can be caused by electrical issues, physical damage, or wear and tear over time. Signs of a faulty light socket include a non-functional light bulb, flickering or dim lighting, or a loose connection.

Symptoms of a bad light socket can include:

• The refrigerator light not turning on 
• Intermittent flickering or dimming of the light
• Difficulty in installing or removing the light bulb
• Visible damage on the socket

Replace your malfunctioning light socket with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Defrost Heater Assembly is an OEM part for Frigidaire refrigerators. It is responsible for preventing excessive frost buildup on the evaporator coils by heating them during the defrost cycle.

A bad defrost heater assembly can be caused by electrical issues, component failure, or damage. When the defrost heater assembly becomes faulty, it can result in issues such as excessive frost accumulation in the freezer, poor cooling performance, or even a complete defrost system failure.

Symptoms of a bad defrost heater assembly include:

• Excessive frost or ice buildup on the evaporator coils
• Poor cooling in the refrigerator or freezer 
• Water leaking or pooling under the refrigerator
• Refrigerator running continuously 

Replace your faulty defrost heater assembly with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

Replacement solenoid that restores electromechanical action for the appliance component it controls, helping restore reliable operation when a worn or failed solenoid prevents movement or actuation. What it does:

• Converts electrical input into mechanical motion to move or hold a controlled mechanism.
• Energizes to engage the component and de-energizes to release it.
• Common symptoms of a failing solenoid: the controlled function doesn't respond, intermittent operation, or a humming/no-movement sound.
• Used as a direct replacement for a failed or sticking solenoid to return normal operation.

• Always disconnect power to the appliance before starting work.
• If the solenoid controls water, shut off the water supply before replacing.
• Match wiring connectors and mounting points; secure the part in the original orientation.
• After installation, restore power/water and test the controlled function for proper operation.

This electronic control board is the appliance's central "brain." It governs power to components, interprets inputs, and coordinates timing so selected functions run reliably and status is shown correctly.

• Coordinates signals from sensors and the user interface to execute programmed cycles
• Switches power to components through onboard relays
• Regulates timing and, where applicable, temperature or cycle parameters
• Typical failure symptoms: dead or erratic display, unresponsive buttons, failure to start, or recurring error codes

• Disconnect power at the breaker or unplug the unit before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and move connectors one at a time to the same positions on the new board
• Mount securely and follow your model's tech sheet for wiring verification and post-install checks

This replacement basket restores secure, organized storage or containment inside your appliance so items stay put and the compartment works like new. It's a direct-fit cosmetic and functional replacement when the original basket is damaged or missing. What it does:

• Provides a sturdy place to hold items and keeps them from shifting or falling through
• Replaces cracked, warped, or broken baskets that no longer support loads
• Helps restore proper airflow or organization where the basket is used
• Prevents stored items from contacting internal components or obstructing operation

• Turn off and unplug the appliance before installing
• Remove any remaining contents and old basket before fitting the new part
• Slide or snap the basket into the existing tracks or mounting points—do not force