Fwxb23rg50 Parts

This rubber lid grommet cushions and seals the lid edge to prevent metal-on-metal contact and reduce vibration and noise. It restores proper lid alignment and helps keep the top surface from chipping or scratching. What it does:

• Acts as a bumper between the lid and cabinet to reduce noise and impact
• Maintains correct lid spacing and alignment for smooth opening/closing
• Protects finish by preventing wear where the lid contacts the cabinet
• Reduces vibrations or rattling caused by a loose or worn grommet

• Accessible with basic tools; remove the lid or open to access mounting location as needed
• Clean mating surfaces before installing to ensure a secure fit
• Inspect adjacent hinges and fasteners while replacing the grommet
• Disconnect power if working near electrical components or moving parts

This lint filter is the replacement screen that traps lint and debris during the wash, helping prevent clogs and improving drain flow for cleaner laundry. It restores the washer's ability to catch fibers before they reach the pump. What it does:

• Screens out lint, hair, and loose fibers from the wash water to reduce redepositing on clothes
• Helps prevent lint buildup in hoses and the drain pump that can cause clogs
• Can reduce odors and drainage issues caused by trapped debris
• Works as a direct replacement for the washer's original lint-screening component

• Disconnect power and water supply before servicing the washer
• Access and remove the old filter per your model's service instructions; refer to the washer's parts diagram for location
• Inspect surrounding seal/gasket and housing for damage; replace if worn to ensure a proper fit

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

This replacement spacer positions the transmission bearing block to help maintain proper alignment and drivetrain spacing for reliable washer operation. It restores correct fit where worn or damaged spacers cause misalignment. What it does

• Centers and supports the transmission bearing block to preserve correct bearing alignment.
• Maintains the designed clearance between transmission components and the tub/drivetrain.
• Helps reduce excess vibration, grinding, or wobble caused by a shifted or worn spacer.
• Can address intermittent agitation or spinning issues when misalignment is the root cause.

• Disconnect power and turn off water supply before beginning service.
• Access requires removing the washer cabinet/tub and supporting the transmission; keep track of fasteners and orientation.
• Inspect nearby bearings, seals, and mounting hardware and replace if worn.

Pan hd phillips ,6-32 x 0.337 ,dog point

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support