Gdf510psj533 Parts

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

The Rack Bracket - 2 Wheels is an OEM part for GE dishwashers. It supports and allows the smooth movement of the dishwasher rack in and out of the machine, providing stability and ease of use during loading and unloading.

Causes of a bad rack bracket can include wear and tear from regular use, accumulation of debris or hard water deposits, or physical damage from overloading or mishandling the rack.

Symptoms of a bad rack bracket include:

• Difficulty sliding the rack in and out
• The rack derailing or not staying in place
• Unusual noises during rack movement
• Visible damage to the bracket or wheels

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This replacement O-Ring restores a watertight seal at an internal dishwasher connection, helping stop leaks and protect surrounding cabinetry. Replace a hardened, cracked, or flattened seal to maintain reliable wash performance and prevent water damage.

• Creates a watertight seal between mating parts inside the dishwasher
• Helps prevent drips and leaks during fill, wash, and drain cycles
• Addresses leaks caused by a worn, flattened, or damaged seal
• Visual clues: cracks, brittleness, deformation, or mineral trails at the joint

• Disconnect power and shut off the water supply before servicing
• Access the affected connection and remove the old O-ring
• Clean the groove and mating surfaces; lightly lubricate with food-grade silicone grease; seat evenly without twisting or pinching
• Reassemble and run a brief test cycle to check for leaks

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

The Main Control Board is an OEM component specifically designed for GE dishwashers. It acts as the central "brain" that facilitates all washing functions. Integrated electronic components and programmed controls coordinate important operations like wash cycles, temps, dispensing, the user interface, and more. Over time electrical connections can degrade or surface mount chips fail.

Causes of a bad control board may arise from power surges, water exposure damage or simply normal component wear over thousands of wash cycles.

Symptoms of a failed control board include:

• The dishwasher failing to start or stopping mid-cycle
• Inability to change wash options or respond to button inputs
•  Strange electrical noises, smells, or error codes displayed

This genuine OEM GE part restores full operational capability with factory programming and reliability. It is also compatible with Hotpoint, RCA, and some Kenmore models for a direct replacement upgrade.

This dishwasher feed tube channels wash water from the sump to the middle spray arm, restoring proper water delivery to help ensure thorough cleaning between racks.

• Directs pressurized water to the middle spray arm during wash cycles
• A worn, cracked, or leaking tube can reduce spray pressure and cleaning performance
• Common symptoms include poor wash results on the middle rack, weak spray, or visible leaks from the conduit area
• Replacing the conduit can resolve intermittent spray or uneven cleaning

• Disconnect power and water supply before servicing
• Remove lower rack and any fasteners/clips securing the conduit; note routing and orientation
• Inspect and transfer any reusable seals or clips only by the manufacturer
• After installation, run a short cycle to check for proper spray and leaks

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

This detergent cup cover attaches to the dishwasher's dispenser to seal the detergent compartment until the control releases it. Replacing a damaged cover prevents early washout and restores consistent detergent release for reliable cleaning results.

• Covers and seals the dispenser's detergent cup
• Opens at the proper time to release detergent into the wash
• Helps prevent detergent leaking or washing out too early
• Typical symptoms: cup won't stay closed, poor cleaning, visible damage to the cover/hinge

• Disconnect power to the dishwasher before servicing
• Handle hinge tabs carefully; transfer and tension the existing spring/pin if your model uses them
• After installation, close and manually release the cover to ensure smooth operation before running a cycle

The Rack Slide is an OEM replacement part for GE dishwashers. It refers to the components that allow the upper rack to glide smoothly in and out. Allowing for continuous movement over extended use, the slides can degrade, causing friction or binding that restricts access to dishes.

Symptoms of bad rack slides include:

• Difficulty fully extending or retracting the racks   
• Noisy operation accompanied by grinding or squeaking noises
• Racks that do not run smoothly and become stuck partially open

Causes of rack slides becoming bad are normal wear and tear from loading and unloading dishes over many years. Motion parts wear out more quickly than stationary components.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Replace a worn or broken tub roller with this Tub Roller and Stud Assembly. It mounts to the dishwasher tub wall to guide the rack smoothly, preventing dragging, binding, or derailment when loading and unloading.

• Mounts on the tub sidewall to provide a smooth glide point for the dish rack
• Restores easy rack movement and can reduce squeaking or scraping noises
• Helps keep the rack aligned and prevents it from jumping off track
• Typical signs of failure: cracked/broken wheel, missing/bent stud, rack difficult to slide

• Disconnect power and water supply before servicing; wear cut-resistant gloves.
• Pull the rack out to access the roller location inside the tub.
• Remove the old roller and stud (retainer/tab/screw varies by model) and install the new assembly in the same orientation.
• Slide the rack in and out to confirm smooth movement before returning the appliance to service.

This arm hinge assembly restores smooth, controlled movement of a hinged component in your dishwasher, helping maintain proper alignment and reliable operation. Replacing a worn or broken hinge can reduce binding, squeaks, and misalignment that affect performance. What it does:

• Provides the pivot point and support for a hinged assembly
• Maintains alignment to ensure correct engagement and sealing
• Helps ensure smooth opening/closing motion without binding
• Replaces a hinge arm that is cracked, bent, or worn
• Common signs: stiff or uneven movement, squeaking or popping noises, misalignment, or visible damage

• 1 arm hinge assembly

• Disconnect power and water before servicing
• Support the door or movable assembly to relieve tension while removing the hinge
• Note orientation and transfer any side-specific hardware from the original part
• After installation, check for smooth motion and proper alignment before restoring power and water