Gdf520pgdww Parts

The Clamp is an OEM replacement part for GE dishwashers. It holds and secures critical components such as tubing or hoses securely in place. Clamps play an important supporting role by fastening tubing and preventing kinking, both of which are essential for proper water flow and circulation within the dishwasher.

Causes of a bad clamp can include cracks, corrosion, or fatigue that causes the clamp to fail in its gripping function over time. Hoses or tubes may also wear down a clamp through constant vibration. 

Symptoms of a bad clamp include:

• Leaks from hoses, tubes or connections  
• Reduced water pressure or uneven spray patterns
• Moisture or water damage around connections
• Loose hoses that rub or chafe

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This vent gasket seals the dishwasher's door vent to keep steam and splashes inside the tub. Replacing a worn seal helps prevent leaks around the vent area and maintains proper moisture control during wash and dry cycles. What it does:

• Seals the vent housing to the inner door liner
• Helps prevent water and steam from escaping at the vent opening
• Addresses leaks or drips from the top/vent area of the door
• Replace if the original gasket is torn, flattened, brittle, or misshapen
• Helps maintain the intended airflow path through the vent assembly

• 1 vent gasket

• Disconnect power to the dishwasher before servicing
• Remove inner door panel screws to access the vent assembly
• Note gasket orientation; clean mating surfaces and seat the new gasket evenly without stretching
• Reassemble and run a short cycle to check the vent area for leaks

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

The Shelf Cup is an OEM component specifically designed for GE dishwashers. It is a rack shelf to provide stability for stemmed glasses. Subject to chemical deterioration and physical stresses, shelf cups can crack or warp over time. 

Symptoms of a bad shelf cup include:

• Cup no longer securely holds stemmed glasses in place during washing 
• Cracks along weakened seams 
• Deformation preventing proper nesting of stemware bases

Causes of shelf cup degradation relate to continuous exposure to hot water and washing chemicals combined with the physical stresses of loading and unloading stemware.

Replace yours today with this genuine GE OEM part to maintain rack integrity. Proper glass support ensures unobstructed wash spray coverage. This GE replacement part is compatible with some Hotpoint, RCA, and Kenmore models.

This grounding plate is a stamped metal bracket that provides a secure electrical ground connection for the appliance, helping protect components and reduce shock risk. It's a direct-replacement part used where the appliance chassis requires a dedicated grounding point. What it does:

• Provides a reliable chassis-to-ground connection for electrical safety.
• Maintains a stable grounding path for control boards and metal panels.
• Helps address symptoms such as intermittent electrical faults, tripped breakers, or grounding-related error codes when a damaged or missing bracket is suspected.
• Replaces a corroded, bent, or broken grounding/mounting plate to restore proper contact.

• One grounding plate

• Turn off power to the appliance at the breaker and unplug before servicing.
• Mount to the specified chassis location using the original screws or fasteners; ensure clean, bare metal contact for a good ground.
• Do not modify the part; if screw holes or fasteners are missing, replace with OEM-specified hardware.

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

This control panel assembly replaces the dryer's main user interface so you can restore responsive buttons, cycle selection, and display feedback. It provides the mounted switches and overlay needed for normal panel operation and user control. What it does

• Houses the push buttons, display window, and circuit board that register user inputs and communicate cycle commands
• Restores unresponsive or erratic button behavior, missing display segments, or incorrect cycle selections
• Reestablishes proper electronic signaling between the console and the dryer's control system
• Helps stop intermittent or nonfunctional control responses tied to a damaged or worn panel assembly

• One control panel assembly as shown

• Disconnect power before beginning service to avoid shock hazard
• Handle the PCB and ribbon connectors carefully to prevent static or connector damage
• Some disassembly of the appliance console is required; follow the manufacturer service manual for step-by-step instructions