Gdf570sgd0bbsj0ss Parts

This vent (dark grey) replaces a damaged or faded exterior vent cover on compatible GE appliances, helping restore appearance and maintain proper airflow. Use it to address visible damage or improve a loose or rattling vent. What it does:

• Covers and protects an appliance vent opening while allowing airflow through the cabinet or housing.
• Helps prevent drafts and keeps debris, lint, and small pests from entering the appliance interior.
• Stops rattling or vibration caused by a cracked or loose vent cover.
• Restores the original look by replacing a faded, cracked, or broken vent piece.

• Disconnect power (and gas, if applicable) before service and work on a cool, unplugged appliance.
• Remove trim or access panels as needed; keep screws and parts organized for reassembly.
• Check fit and orientation before final fastening to ensure proper airflow and sealing.

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This manual floor plate is the replacement cover that mounts at the appliance base to protect internal components and provide a finished surface. It restores the dryer's base appearance and helps prevent debris from entering the cabinet. What it does:

• Covers and protects the lower cabinet opening and components from dust and lint
• Helps maintain proper clearance and a finished look at the dryer base
• Replaces damaged, bent, or missing base plates that allow debris entry
• Can reduce rattles or vibration caused by a loose or warped floor plate

• One floor plate

• Disconnect power (and gas, if applicable) before servicing to avoid shock or injury
• Remove the dryer front or lower access panel per manufacturer instructions to access mounting screws
• Use correct-size screws and tighten to manufacturer torque; avoid over-bending the plate during installation

Left side roller cover.

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

This silicone light pipe guides an appliance's indicator or control panel light to the front-facing bezel so lights appear bright and centered. It restores proper light transmission for clearer, easier-to-read controls. What it does:

• Transmits LED or bulb light from the lamp housing to the control surface or bezel
• Helps ensure indicator lights and touch-control icons appear centered and visible
• Commonly replaced when the lens is cracked, torn, missing, or deformed
• Can resolve symptoms like dim, distorted, or missing panel illumination

• Disconnect power before servicing any electrical or control components
• Remove the control panel or bezel per your model's service instructions to access the light pipe
• Handle the silicone gently—avoid stretching or pinching that could deform the part
• Ensure the light pipe is fully seated in its housing and the bezel is reinstalled to prevent light leaks

Replacement control box top that restores the protective cover for the appliance control housing, keeping wiring and electronics enclosed for a cleaner appearance and safer operation. What it does:

• Covers and protects the control housing and internal wiring from dust, spills, and accidental contact
• Helps secure control components in place and maintain the appliance's factory appearance
• Commonly replaced when the original cover is cracked, broken, missing, or shows visible damage
• Can prevent loose wiring from catching or being accidentally disturbed

• One control box top

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Remove any screws or retainers securing the existing cover and lift off the old top; keep fasteners if reinstalling
• Align the replacement top and secure with the original fasteners; ensure wiring is routed and seated before closing

Note: This kit contains both the Circulation Pump and Drain Pump along with a harness and clamps. Due to a factory revision, the pumps are no longer offered individually.

The Clamp is an OEM replacement part for GE dishwashers. It holds and secures critical components such as tubing or hoses securely in place. Clamps play an important supporting role by fastening tubing and preventing kinking, both of which are essential for proper water flow and circulation within the dishwasher.

Causes of a bad clamp can include cracks, corrosion, or fatigue that causes the clamp to fail in its gripping function over time. Hoses or tubes may also wear down a clamp through constant vibration. 

Symptoms of a bad clamp include:

• Leaks from hoses, tubes or connections  
• Reduced water pressure or uneven spray patterns
• Moisture or water damage around connections
• Loose hoses that rub or chafe

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This vent gasket seals the dishwasher's door vent to keep steam and splashes inside the tub. Replacing a worn seal helps prevent leaks around the vent area and maintains proper moisture control during wash and dry cycles. What it does:

• Seals the vent housing to the inner door liner
• Helps prevent water and steam from escaping at the vent opening
• Addresses leaks or drips from the top/vent area of the door
• Replace if the original gasket is torn, flattened, brittle, or misshapen
• Helps maintain the intended airflow path through the vent assembly

• 1 vent gasket

• Disconnect power to the dishwasher before servicing
• Remove inner door panel screws to access the vent assembly
• Note gasket orientation; clean mating surfaces and seat the new gasket evenly without stretching
• Reassemble and run a short cycle to check the vent area for leaks