Gdf570ssfoss Parts

This upper spray arm gasket seals the hub where the arm connects, keeping wash water routed through the upper arm. Replace a worn seal to restore upper-rack spray performance and reduce internal leaks or water bypass.

• Creates a watertight seal at the upper spray arm connection
• Helps maintain proper water pressure and spray pattern to the upper rack
• Replaces a cracked, flattened, or missing gasket
• Common symptoms: poor upper-rack cleaning, weak/erratic upper spray, dripping at the spray arm hub inside the tub

• Disconnect power and water supply before servicing
• Remove the upper spray arm (and rack if needed) per your model's procedure
• Lift out the old gasket; clean the sealing surfaces; press the new gasket fully and evenly into place
• Reassemble and run a short test cycle to check for proper spray and leaks

The Friction Washer is an OEM component specifically designed for GE dishwashers. This friction washer is a thin circular part that creates resistance through surfaces rubbing together. It is often used beneath a mounting nut to prevent components from loosening during operation.  

Symptoms of a bad friction washer include loose or separating connections where the washer is installed, such as:

• Drain pump mounting fittings that become detached    
• Water connections that leak at the threaded joints
• Door handle mounts that allow play in the mechanism

Causes of failure can be cracks, wear or deformities in the washer that reduce its friction capabilities over time. Vibrations from use may also cause premature wear.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This left-hand attachment strip secures trim and panels for a clean, finished fit on compatible GE appliances. It helps maintain proper alignment and prevents gaps that can collect dirt or allow panels to shift during use. What it does:

• Attaches and stabilizes a side trim or panel to the appliance cabinet
• Keeps door/side trim aligned to reduce rattling or shifting
• Helps maintain an even, finished appearance along the appliance edge
• Addresses symptoms like loose trim, visible gaps, or panel movement

• One left-hand attachment strip

• Remove power to the appliance (or disconnect power source) before starting work
• Use basic hand tools; avoid forcing parts to prevent breakage
• Replace with OEM-specified hardware if fasteners are missing or damaged

This dishwasher hose clamp secures internal hoses to pumps or fittings, helping prevent leaks and disconnections. Replace a weakened or damaged clamp to restore a tight, reliable seal at the connection.

• Provides clamping pressure to hold a hose on pump, sump, or drain fittings
• Helps stop water leaking at hose joints
• Resolves: loose or disconnected hoses, water under the unit/base, or poor draining from a slipped drain hose
• Replaces worn, rusted, or deformed clamps after service

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward as needed for access; place a towel or pan to catch residual water
• Seat the hose fully, then compress or tighten the clamp per its design; position just behind the hose barb bead
• Run a short cycle and inspect for leaks at the connection

The Sump Manifold is an OEM component specifically designed for GE dishwashers. It is located within the sump pan and functions as an integral part of the dishwasher's drainage and circulation system. The sump manifold directs water flow during draining and refilling, ensuring proper water distribution to different areas of the dishwasher for cleaning and rinsing cycles. 

Symptoms of a bad sump manifold include:

• Issues with draining and water drainage
• Leaks within the sump pan area 
• Reduced or uneven water pressure during wash cycles
• Improper filling or distribution of water

Over time, components inside the sump manifold can break down or become clogged due to mineral buildup or leftover food particles. Regular maintenance is recommended to keep the sump manifold functioning optimally. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This vent gasket seals the dishwasher's door vent to keep steam and splashes inside the tub. Replacing a worn seal helps prevent leaks around the vent area and maintains proper moisture control during wash and dry cycles. What it does:

• Seals the vent housing to the inner door liner
• Helps prevent water and steam from escaping at the vent opening
• Addresses leaks or drips from the top/vent area of the door
• Replace if the original gasket is torn, flattened, brittle, or misshapen
• Helps maintain the intended airflow path through the vent assembly

• 1 vent gasket

• Disconnect power to the dishwasher before servicing
• Remove inner door panel screws to access the vent assembly
• Note gasket orientation; clean mating surfaces and seat the new gasket evenly without stretching
• Reassemble and run a short cycle to check the vent area for leaks

The Tine Block is an OEM component specifically designed for GE dishwashers. It refers to the horizontal arm that rotates during the wash cycle, hitting dishes with jets of water from hidden nozzles. Over many cycles of use, normal wear and tear can cause some degradation.

Causes of a bad tine block can include mineral and chemical buildup inside the nozzles over time, reducing water spray pressure.

Symptoms of a bad tine block include:  

• Poor water coverage of dishes failing to adequately rinse away soils
• Diminished cleaning performance as water pressure weakens
• Clogged or kinked supply hoses preventing consistent flow to nozzles

Replace yours today with this genuine GE OEM component to restore optimized washing. Proper spray coverage is needed to remove baked-on residues. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

This top attachment strip secures the appliance's top panel and provides the mounting point for the door strike, restoring a stable, properly aligned front. It prevents panel movement and reduces rattles for a snug fit and reliable door engagement. What it does:

• Secures the top/front panel to the cabinet to maintain alignment and fit
• Serves as the mounting point for the door strike or latch components
• Helps eliminate rattling, vibration, and gaps at the top of the door area
• Restores reliable door engagement and prevents the strike from shifting

• Disconnect power to the appliance before beginning any repair
• Remove the top panel or access screws to reach the attachment strip; a screwdriver set is typically required
• Handle mounting tabs and edges carefully to avoid bending or damage
• Verify alignment of the door strike and test door closure after installation

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing