Gdp280edoww Parts

This Silverware Blaster Assembly directs targeted rinse water to the silverware basket so forks, spoons and knives come out cleaner. It replaces a worn or broken blaster to restore focused spray coverage for better wash results. What it does:

• Channels pressurized wash water to the silverware area to improve cleaning of utensils
• Replaces a cracked, clogged, or non-rotating blaster that can leave silverware dirty
• Helps restore normal spray pattern when the original blaster is missing or damaged
• Works with the lower rack silverware basket to target hard-to-reach items

• Disconnect power and shut off water supply before starting any repair
• Remove lower rack to access and remove the old blaster; inspect surrounding clips and seals
• Snap or screw the new assembly into place; ensure it turns freely and is not obstructed
• Run a short rinse cycle to verify proper spray and correct installation

This control box bottom is the lower housing piece that secures and protects the appliance control board and related components. It restores a stable mounting surface and helps keep electronics shielded from vibration and debris. What it does:

• Provides the lower half of the control box housing to support and protect the control board
• Keeps wiring and connectors routed and held in place to prevent strain
• Replaces cracked, broken or warped housing that can expose electronics
• Helps stop rattling or movement of the control assembly that can cause intermittent controls

• Control box bottom

• Power off and unplug the appliance before starting any repair
• Handle the control board and connectors carefully to avoid electrostatic or mechanical damage
• This part typically installs with screws or clips; retain fasteners and note their locations during disassembly
• Inspect and address the electronics before reassembly

A small mounting clip that secures interior panels or trim pieces to the appliance, keeping parts aligned and preventing rattling or movement during operation. Simple replacement restores proper fit and reduces noise from loose components. What it does:

• Holds a panel, trim or small component in place on the cabinet or housing
• Keeps parts aligned so doors, panels or covers fit and operate smoothly
• Prevents rattling or vibration caused by loose or missing fasteners
• A worn or broken clip can allow gaps, movement, or noise during use

• Disconnect power (unplug or switch off breaker) before servicing
• Replacement typically requires only basic hand tools; keep track of any removed fasteners
• Inspect surrounding mounting points and adjacent clips for wear and replace as needed

Color: White. Size: 13 oz. Spray paint primer. can.

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

Left side roller cover.

The User Interface Housing is an OEM replacement part for GE dishwashers. Located at the front of the console, it houses the control panel responsible for cycle/option navigation.

The housing protects sensitive electronic components from water damage and physical impact. Its sturdy construction allows for responsive touch inputs without flex or play in the assembly. 

Symptoms of a bad user interface housing include:

• Warping or cracks exposing circuitry to damage
• Faulty sealing allowing moisture penetration
• Difficulty registering button presses from structural defects
• Ill-fitting installation negatively impacting usability

Causes can be repetitive openings allowing entry of dirt/moisture into critical areas and use over the years breaking down seals and weakening materials.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This is a genuine replacement mounting screw used to secure components in compatible Frigidaire appliances. It restores proper fastening so panels and parts stay aligned and stable during normal operation. What it does:

• Fastens appliance components, panels, or brackets to maintain secure assembly
• Replaces worn, stripped, or missing screws that cause rattling or loose parts
• Helps eliminate vibration-related noise by restoring correct fastening
• Matches OEM fit and function for reliable, long-lasting hold

• One replacement mounting screw, as pictured

• Use the proper size driver to avoid stripping the head; tighten until snug but do not overtighten
• Match screw location and length to the original for correct fit; keep any removed hardware for reference
• Disconnect power to the appliance before working in internal areas to reduce shock risk

This is a replacement screw used to secure appliance panels and components, restoring proper fit and stopping looseness or rattling. It's a direct-fit fastener that helps maintain safe, stable operation when original hardware is missing or worn. What it does

• Secures panels, brackets, trim pieces or internal components in place
• Stops rattling or vibration caused by loose fasteners
• Helps maintain proper alignment of parts for reliable operation
• Restores missing or damaged mounting hardware

• Screw

• Disconnect power (and water if applicable) before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or parts
• Keep removed hardware organized before final assembly

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

The Screw is an OEM part for GE dishwashers. This screw is designed for various applications, including securing and fastening components in your GE appliance.

A bad screw can result in issues such as loose or unstable components, improper functioning, or even potential damage to other parts. Causes of a bad screw can include wear and tear over time, improper installation, or exposure to extreme conditions.

Symptoms of a bad Screw include:

• Components becoming loose or detached
• Parts not securely fastened
• Unusual noises or vibrations during operation
• Visible signs of damage or wear on the screw

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This silverware basket conduit is the replacement channel that helps secure and guide the dishwasher silverware basket, restoring proper fit and reducing movement during cycles. It brings back stable basket positioning for safer cleaning. What it does:

• Replaces a worn, cracked, or missing conduit that holds or guides the silverware basket
• Prevents the basket from shifting, rattling, or catching on the rack during wash cycles
• Restores correct basket alignment so utensils are held securely for effective cleaning
• Fits and functions as the OEM-designed support channel for the silverware basket assembly

• Disconnect power and water supply before beginning any repair
• Remove the dishwasher rack to access the conduit; handle racks carefully to avoid damage
• Inspect mounting clips or tabs and remove any broken pieces before installing the new conduit

This rail and end cap assembly secures a refrigerator shelf or door bin and restores a stable mounting surface for stored items. It replaces worn or damaged rails that allow shelves to sag or detach. What it does

• Replaces a damaged shelf rail and end cap to restore proper shelf support
• Holds the shelf/bin in position so items stay level and don't slide off
• Stops rattling or movement caused by a loose or broken rail assembly
• Fits where an original molded rail/end cap has cracked, worn, or failed

• One rail and end cap assembly as shown

• Remove food and bins from the area before starting; support the shelf while removing the old part
• Use basic hand tools; avoid forcing parts — align tabs and slide the rail into place until it snaps or seats
• Disconnect power if required by your model before working near electrical components