Gdp280edoww Parts

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This left-side door trim piece restores the exterior appearance and proper fit of a damaged or worn appliance door. It replaces cracked, chipped, or loose trim to help the door close and sit correctly in the frame. What it does:

• Covers and protects the left edge of the door while providing a finished appearance
• Replaces cracked, broken, or cosmetically damaged trim
• Helps maintain correct alignment of the door edge and attachment points
• Secures to the door with factory mounting tabs or screws
• Useful when left-side trim has snapped, warped, or come loose

• One left side door trim

• Disconnect power and/or fuel supply before beginning any repair
• Use appropriate hand tools; support the door to prevent dropping or damage
• Inspect mounting tabs and nearby components; replace any broken fasteners
• Follow the appliance service manual for disassembly and torque/spec guidance

This user interface harness connects the oven/dryer control console to the main wiring, restoring reliable signal and power between the control and components. It's used when the console wiring is damaged or intermittent. What it does:

• Routes signals and power from the control panel to the appliance's main control and components
• Replaces frayed, burnt, or broken console wiring that can cause intermittent or non-working controls
• Helps fix symptoms such as unresponsive buttons, faulty display/LED behavior, or inconsistent cycle starts
• Preserves factory routing and connector fit for correct electrical connections

• One user interface wiring harness assembly

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or damage
• Handle connectors gently and match keyed plugs; do not force connections
• Inspect mating connectors on the control and console for damage before installing

This AC harness is the wiring assembly that connects the air conditioning system's electrical components, providing organized power and signal routing for reliable operation. Replaces worn or damaged harnesses to restore proper electrical connections. What it does:

• Routes power and low-voltage signals between A/C components (compressor, fan, controls) for coordinated operation
• Helps prevent intermittent faults caused by loose, frayed, or corroded wires
• Can resolve symptoms such as the A/C not starting, intermittent compressor or fan operation, or blown fuses
• Maintains correct connector fit and wire routing to reduce stress on terminals

• One AC wire harness

• Turn off power at the breaker and confirm zero voltage before servicing
• Match connectors and wire colors; secure harness along original routing to avoid heat or moving-part damage
• Inspect connector terminals and mating components for corrosion—clean or replace as needed

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

This fill funnel hose directs incoming water from the inlet area into the washer tub to prevent splashing and misdirected flow. It helps maintain proper water routing for reliable fills and reduces chances of internal leaks. What it does:

• Guides incoming water from the fill/inlet area into the tub to avoid spraying or pooling
• Helps prevent water from entering cabinet areas or dripping onto components
• Can resolve symptoms like water spraying near the top of the tub, water pooling under the washer, or irregular fill routing
• Works with the washer's inlet/fill assembly to keep fill flow focused and controlled

• One fill funnel hose

• Disconnect power and shut off water supply before starting any repair
• Replace only with the exact part number shown;
• Inspect nearby fittings, clamps, and seals and replace if damaged to ensure a watertight connection

This service inner door assembly replaces a damaged or worn inner door panel to restore proper sealing and appearance inside the appliance door. It helps ensure the door closes correctly and protects internal components from debris and wear. What it does:

• Replaces the inner door panel/assembly to restore the door's internal structure and fit
• Helps stop rubbing, scraping noises or misalignment caused by a damaged inner door
• Protects internal components and gasket areas from debris and wear
• Restores proper surface for door latch and sealing interfaces

• One service inner door assembly

• Designed for technicians or experienced DIYers; refer to the appliance service manual for step-by-step disassembly/reassembly
• Disconnect power (and water if applicable) before starting work to avoid shock or water damage
• Use proper tools and support the outer door to prevent drops or damage while removing/installing the inner door
• Inspect door seals, hinges and fasteners during reassembly; replace any worn hardware as needed