Gdt535 Parts

This replacement O-Ring restores a watertight seal at an internal dishwasher connection, helping stop leaks and protect surrounding cabinetry. Replace a hardened, cracked, or flattened seal to maintain reliable wash performance and prevent water damage.

• Creates a watertight seal between mating parts inside the dishwasher
• Helps prevent drips and leaks during fill, wash, and drain cycles
• Addresses leaks caused by a worn, flattened, or damaged seal
• Visual clues: cracks, brittleness, deformation, or mineral trails at the joint

• Disconnect power and shut off the water supply before servicing
• Access the affected connection and remove the old O-ring
• Clean the groove and mating surfaces; lightly lubricate with food-grade silicone grease; seat evenly without twisting or pinching
• Reassemble and run a brief test cycle to check for leaks

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This fill funnel assembly mounts inside the dishwasher tub at the water inlet. It directs incoming water into the tub and helps prevent splashing or leaks at the fill area for reliable fills and cleaner operation.

• Channels water from the inlet opening directly into the tub
• Helps control splash and seal the fill port to reduce drips
• Damage, cracks, or a missing funnel can cause leaks near the fill area during the fill cycle or unusual spraying sounds
• Restores proper water entry path for consistent filling

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the fill inlet on the tub wall
• Remove retaining fastener(s) or tabs, replace the funnel, and ensure any seal is properly seated
• Reassemble and run a brief fill/rinse to check for leaks at the inlet area

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This pump isolator hanger secures and cushions the dishwasher's pump assembly, helping reduce vibration and noise while keeping the pump properly supported. Replacing a worn hanger restores stable, quieter operation and maintains correct pump alignment.

• Supports and isolates the pump assembly beneath the tub to dampen vibration
• Helps keep the pump properly positioned and prevents contact/rattling
• Replace if the hanger is stretched, cracked, or broken
• Common symptoms include louder operation, rattling from the base, or a sagging pump assembly

• Disconnect power and shut off water before servicing; wear gloves and eye protection
• Access from the front base by removing the toe-kick/kickplate; support the pump assembly
• Detach the worn hanger from its mounting points and install the new hanger in the same locations
• Ensure the pump is secure, hoses/wires aren't strained, and run a brief test for noise/vibration

This heater nut secures the dishwasher's heating element where it passes through the tub, helping maintain a tight connection and proper positioning. Replacing a damaged or missing nut can help prevent leaks and keep the element stable.

• Fastens the heating element to the tub from below to hold it firmly in place
• Helps support a watertight connection at the element pass-through when used with the proper seal
• Replace if the nut is cracked, heat-damaged, stripped, or missing
• Common symptoms include water leaking under the unit near the heater terminals and a loose or wobbly heating element

• Disconnect power at the breaker and shut off water before servicing
• Access the nut from beneath the dishwasher; remove the toe-kick and pull the unit forward if needed
• Support the element from inside the tub while tightening; snug gently and do not overtighten to avoid damage
• Restore power/water and run a short cycle to check for leaks

This dishwasher feed tube channels wash water from the sump to the middle spray arm, restoring proper water delivery to help ensure thorough cleaning between racks.

• Directs pressurized water to the middle spray arm during wash cycles
• A worn, cracked, or leaking tube can reduce spray pressure and cleaning performance
• Common symptoms include poor wash results on the middle rack, weak spray, or visible leaks from the conduit area
• Replacing the conduit can resolve intermittent spray or uneven cleaning

• Disconnect power and water supply before servicing
• Remove lower rack and any fasteners/clips securing the conduit; note routing and orientation
• Inspect and transfer any reusable seals or clips only by the manufacturer
• After installation, run a short cycle to check for proper spray and leaks

The White Toe Kick is an OEM component specifically designed for GE dishwashers. This toe kick forms the lower front panel of the dishwasher beneath the door. It is responsible for providing a finished look and protecting the inner components. 

The toe kick can become faded, cracked, or warped over time due to repeated cleaning. Improper cleaning methods may also damage the surface of the toe kick. 

Symptoms of a damaged toe kick include:

• Discoloration or fading of the white surface
• Cracks or chips in the paint/finish
• Warping that causes gaps around the door seal

This replacement part is also compatible with Profile, Hotpoint, RCA, and select Kenmore models.

This left-hand rack slide end cap restores the stop at the end of your dishwasher's rack rail. It keeps the rack secured on the slide and ensures controlled travel when the original cap is broken or missing.

• Snaps onto the left rack slide/rail to act as a retention stop
• Helps keep the rack aligned and prevents it from pulling completely out
• Typical symptoms: rack slides out too far, falls off the rail, or the end cap is broken/missing
• Maintains proper rack retention to reduce spills and track damage

• Disconnect power and shut off water before service
• Pull the rack forward to access the end of the left slide rail (left side when facing the dishwasher)
• Release the locking tab to remove the old cap; align and push the new cap onto the rail until it clicks
• Slide the rack in and out to confirm smooth travel and a positive stop

This clip bracket attaches to the dishwasher rack to secure a rack-mounted component or accessory. Replace a cracked or missing bracket to keep parts firmly in place so the rack loads easily and performs as designed.

• Attaches to the rack to hold the mating part securely in place
• Helps prevent shifting, rattling, or accessories falling off during cycles
• Restores proper fit when the original clip is broken, worn, or missing
• Typical signs: accessory won't stay attached, clip is visibly cracked or missing, loose components during operation

• Disconnect power at the breaker and turn off the water supply
• Pull out the rack to access the clip location
• Release the old clip's locking tabs and remove; align and snap the new clip firmly in place
• Verify a secure fit before reinstalling the rack and running a test cycle

This top-control console is the panel at the upper edge of the dishwasher door. It forms the interface area for selecting cycles and protects the components behind it, helping keep the controls aligned and presentable.

• Houses and protects the user interface at the top edge of the door
• Provides the interface area for cycle and option selection
• Restores fit and appearance when the original console is cracked, warped, or loose
• Help if buttons feel misaligned due to a damaged console housing

• Disconnect power at the breaker before servicing; shut off water if moving the appliance.
• Open the door and remove perimeter screws to separate inner/outer door panels; support wiring when removing the console.
• Transfer any model-specific components from the original console to the new console; avoid pinching harnesses during reassembly.
• Restore power and selections engage and the door latches properly.

Size: 10-32 GXTT FLP.595 S

This detergent cup cover attaches to the dishwasher's dispenser to seal the detergent compartment until the control releases it. Replacing a damaged cover prevents early washout and restores consistent detergent release for reliable cleaning results.

• Covers and seals the dispenser's detergent cup
• Opens at the proper time to release detergent into the wash
• Helps prevent detergent leaking or washing out too early
• Typical symptoms: cup won't stay closed, poor cleaning, visible damage to the cover/hinge

• Disconnect power to the dishwasher before servicing
• Handle hinge tabs carefully; transfer and tension the existing spring/pin if your model uses them
• After installation, close and manually release the cover to ensure smooth operation before running a cycle

The Rack Slide is an OEM replacement part for GE dishwashers. It refers to the components that allow the upper rack to glide smoothly in and out. Allowing for continuous movement over extended use, the slides can degrade, causing friction or binding that restricts access to dishes.

Symptoms of bad rack slides include:

• Difficulty fully extending or retracting the racks   
• Noisy operation accompanied by grinding or squeaking noises
• Racks that do not run smoothly and become stuck partially open

Causes of rack slides becoming bad are normal wear and tear from loading and unloading dishes over many years. Motion parts wear out more quickly than stationary components.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.