Gdt535pyv6fs Parts

This AC harness assembly carries incoming line voltage through the dishwasher to the control and other components. Replacing a damaged or heat-stressed harness restores safe, reliable power distribution and can resolve dead controls, no-start, or intermittent power issues.

• Distributes AC power from the dishwasher's power connection to the control and key components
• Provides correct wire routing with factory-terminated connectors for a secure fit
• Replace if wires are cut or melted, or if terminals show heat damage or looseness
• Common symptoms: won't power up or start, dead controls, intermittent power loss

• Disconnect power at the circuit breaker before servicing; verify power is off
• Remove toe-kick and access panels to reach the harness; note original routing and clips
• Move one connector at a time to the new harness; seat fully without forcing and avoid pinching
• Use the model's wiring diagram to confirm connections; secure wiring and reinstall panels

This vent gasket seals the dishwasher's door vent to keep steam and splashes inside the tub. Replacing a worn seal helps prevent leaks around the vent area and maintains proper moisture control during wash and dry cycles. What it does:

• Seals the vent housing to the inner door liner
• Helps prevent water and steam from escaping at the vent opening
• Addresses leaks or drips from the top/vent area of the door
• Replace if the original gasket is torn, flattened, brittle, or misshapen
• Helps maintain the intended airflow path through the vent assembly

• 1 vent gasket

• Disconnect power to the dishwasher before servicing
• Remove inner door panel screws to access the vent assembly
• Note gasket orientation; clean mating surfaces and seat the new gasket evenly without stretching
• Reassemble and run a short cycle to check the vent area for leaks

The Drain Hose is an OEM part for GE dishwashers. It removes wastewater from the dishwasher during each wash cycle.

A bad drain hose can occur due to wear and tear, blockages, or damage from kinks or leaks. If you notice symptoms such as water not draining properly from the dishwasher, leaks around the hose connection, or foul odors coming from the dishwasher, it may be time to replace this part.

Symptoms of a bad drain hose include:

• Improper drainage of water from the dishwasher
• Leaks around the hose connection
• Foul odors coming from the dishwasher

Replace your worn-out or damaged Drain Hose with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This rear third-rack end cap replaces the plastic end piece that secures the dishwasher's third rack to its track, restoring proper alignment and smooth sliding. Ideal for replacing cracked, broken, or missing rear end caps. What it does:

• Secures the third rack to the rear track so the rack stays aligned during use
• Provides a smooth contact point for the rack to slide on and reduces binding or catching
• Replaces cracked, broken or missing rear end caps that can cause rack drift or instability
• Common symptoms this part can fix: rack falls off track, rear rack sits unevenly, scraping or rough movement when sliding the rack

• Disconnect power to the dishwasher before beginning repairs for safety
• Pull the third rack out to access the end cap; remove the old cap and snap the replacement into place
• No special tools are typically required; a flat screwdriver can help if the old cap is stuck
• After installation, slide the rack in and out a few times to ensure secure fit and smooth movement

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

The Door Hinge Assembly right is an OEM component specifically designed for GE dishwashers. This door hinge assembly is located on the right side of the dishwasher door and is responsible for securely and smoothly mounting the door while enabling its opening and closing motion.  

Causes of a bad Door Hinge Assembly Right include loose or stripped screws, worn out bearings or bushings, or bent or fatigued metal from repeated use. 

Symptoms of a bad door hinge assembly include:

• The door not latching or sealing properly
• Difficulty opening and closing the door  
• Excessive noise or vibration from the door
• Misalignment that causes the door to rub or interfere

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This pump isolator hanger cushions and secures the washer drain pump to reduce vibration and noise while keeping the pump properly positioned for reliable water flow. Replaces worn or broken hangers to restore stable pump mounting. What it does

• Cushions the drain pump to reduce vibration and rattling during spin and drain cycles
• Keeps the pump aligned to prevent rubbing, misalignment noise, or premature wear
• Helps maintain a secure pump connection to reduce movement that can lead to leaks
• Used when hanger is cracked, torn, missing, or allowing excessive pump movement

• One pump isolator hanger (single piece as shown)

• Disconnect power and turn off water supply before starting any repair
• Drain remaining water from the washer and access the pump per your model's service instructions
• Inspect surrounding mounting tabs and fasteners; replace any damaged hardware

This replacement screw fastens and secures appliance components where a 1/4-28 threaded flange screw with an internal hex washer head is required. It restores proper fit and helps prevent movement or rattling of panels and assemblies. What it does:

• Secures panels, brackets and components that use a 1/4-28 threaded flange screw
• Internal hex washer head allows a compact, low-profile drive for tight spaces
• Helps stop looseness, vibration noise, and misalignment when the original fastener is missing or worn
• Matches OEM fit and fastening form for reliable reassembly

• Disconnect power and follow all appliance safety procedures before servicing
• Use the correct hex driver/socket to avoid stripping the head
• Tighten to snug fit—do not overtighten to avoid damaging threads or mating parts
• Replace with identical part number to ensure proper fit and function

The Door Hinge Assembly Left is an OEM component specifically designed for GE dishwashers. This door hinge assembly is located on the left side of the dishwasher door and is responsible for securely and smoothly mounting the door while enabling its opening and closing motion.  

Causes of a bad Door Hinge Assembly Left include loose or stripped screws, worn out bearings or bushings, or bent or fatigued metal from repeated use. 

Symptoms of a bad door hinge assembly include:

• The door not latching or sealing properly
• Difficulty opening and closing the door  
• Excessive noise or vibration from the door
• Misalignment that causes the door to rub or interfere

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This grounding plate is a stamped metal bracket that provides a secure electrical ground connection for the appliance, helping protect components and reduce shock risk. It's a direct-replacement part used where the appliance chassis requires a dedicated grounding point. What it does:

• Provides a reliable chassis-to-ground connection for electrical safety.
• Maintains a stable grounding path for control boards and metal panels.
• Helps address symptoms such as intermittent electrical faults, tripped breakers, or grounding-related error codes when a damaged or missing bracket is suspected.
• Replaces a corroded, bent, or broken grounding/mounting plate to restore proper contact.

• One grounding plate

• Turn off power to the appliance at the breaker and unplug before servicing.
• Mount to the specified chassis location using the original screws or fasteners; ensure clean, bare metal contact for a good ground.
• Do not modify the part; if screw holes or fasteners are missing, replace with OEM-specified hardware.

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

This mount tub assembly secures the washer tub to the cabinet and helps keep the tub properly aligned during operation for stable, quieter performance. It replaces a worn or damaged tub mounting component to reduce movement and noise. What it does:

• Supports and centers the wash tub inside the washer cabinet.
• Dampens tub movement to reduce vibration and noise during spin cycles.
• Helps maintain proper tub alignment to prevent rubbing or banging.
• Commonly used when visible tub wear, excessive vibration, or noise occurs.

• Recommended for users familiar with appliance disassembly; disconnect power and water before starting.
• Inspect surrounding seals, mounts, and suspension components and replace if worn.
• Use appropriate tools and follow the washer's service manual for reassembly torque and alignment.

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness