Gdt625psjoss Parts

This small plastic clip secures a refrigerator's wiring conduit or harness to the cabinet, keeping wires routed and protected from abrasion. It helps reduce strain on connections and prevents wires from contacting moving parts. What it does:

• Holds wiring conduit or harness in place to maintain neat routing
• Prevents wires from rubbing on sharp edges or moving components
• Reduces strain on electrical connections that can cause intermittent faults
• Helps maintain safe separation between wiring and high-heat or mechanical areas

• Turn power off at the appliance and unplug before inspecting or replacing wiring clips
• Remove access panels only as needed to reach the clip; avoid stressing surrounding wires
• Snap the clip into the original mounting slot or replace any damaged fasteners for a secure fit
• If wires show damage or burns, replace the wiring/harness

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

This bottom-front foam insulation piece replaces the damaged or missing pad under the refrigerator's front base to help maintain proper airflow and thermal separation for more consistent cooling and reduced condensation risk. What it does:

• Replaces worn or crushed insulation at the refrigerator's lower front to restore intended thermal barrier.
• Helps limit warm air intrusion at the cabinet base that can contribute to frost or uneven temperatures.
• Reduces risk of condensation on the cabinet floor and improve overall efficiency when installed correctly.
• Restores correct spacing and support for the lower access area to prevent drafts.

• Disconnect power and remove the toe grille or front access panel before attempting replacement.
• Handle foam carefully — avoid tearing and align the pad to fit flush with surrounding insulation.
• Use existing clips/adhesive or OEM-recommended fasteners; replace adhesives if brittle or missing.

The Filter Adapter is an OEM component specifically designed for GE dishwashers. Located inside the dishwasher tub, it functions to strain out large food particles from water before it reaches the wash arms.  The adapter holds the removable wash/rinse filters in place during operation, functioning as an extension of the filtration system. 

Causes of a bad filter adapter can include cracks or breaks compromising its sealing surface, wear and tear deforming filter retention features over time, or buildup inhibiting functionality.

Symptoms of a bad filter adapter include:  

• Loose or falling out removable filters during washing  
• Bypassing of food particles around compromised seals
• Reduced lifespan of disposable filters placed in a faulty adapter
• Debris accumulation impacting spray arm performance

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance

This outer door assembly replaces a damaged or worn exterior door panel and restores the appliance's appearance and proper door closure. The stainless steel finish provides a durable, corrosion-resistant surface that matches factory styling. What it does:

• Replaces the exterior door panel to restore correct door fit and finish
• Helps ensure the door closes securely and reduces gaps that can cause heat or air loss
• Stops visible damage such as dents, scratches, or warped edges from affecting operation
• Reduces rattling or vibration caused by a loose or bent outer door

• Disconnect power (and gas supply, if applicable) before starting any repair
• Handle edges and glass carefully to avoid cuts or breakage
• Basic hand tools are typically required; follow the OEM service manual for proper disassembly and reassembly

This door foam block cushions and seals the appliance door, helping reduce vibration and prevent drafts or leaks where the door meets the cabinet. It replaces worn or damaged foam to restore a tight, even door fit and quieter operation. What it does:

• Replaces the foam block located on the appliance door to restore proper sealing and contact
• Helps reduce noise and vibration caused by door movement or uneven contact
• Minimizes air or water leakage at the door seal when original foam is compressed or degraded
• Simple, passive component—no electrical function

• Install by removing the door trim or access panel per your model's service instructions
• Ensure the mounting surface is clean and dry before placing the foam for best adhesion and fit
• Use basic hand tools; avoid forcing the foam into place to prevent tearing
• Disconnect power and follow manufacturer safety guidance before servicing the appliance

This replacement foam block cushions and seals the top control area to reduce vibration and help keep the control assembly securely positioned. It restores proper fit and helps prevent noises or rubbing from loose panels. What it does:

• Cushions the top control assembly to reduce vibration and rattle during operation
• Helps keep control housing and wiring harnesses stable and correctly positioned
• Provides a protective barrier to limit dust and light moisture intrusion around controls
• Addresses symptoms like buzzing/rattling noises or a loosely seated control panel

• Disconnect power to the appliance before starting any repair
• Access the top control area per your model's service instructions; remove trim or console as needed
• Remove old foam and adhesive residue; press replacement foam into correct position ensuring proper orientation

This lens and adhesive assembly replaces a worn, cracked, or cloudy control/display lens and secures the lens to the appliance for a clean, finished appearance and protected electronics. Restores visibility and prevents debris entry behind the lens. What it does:

• Replaces a damaged or discolored control/display lens to improve visibility and aesthetics
• Includes adhesive to secure the lens and maintain a sealed fit over controls or indicators
• Protects underlying buttons, LEDs, and circuit components from dust and moisture
• Helps restore original appearance after impact, cracking, or peeling

• Disconnect power before servicing to avoid shock or unintended appliance operation
• Clean and dry mounting surface; remove old adhesive residues for proper adhesion
• Align lens carefully, press into place, and hold per adhesive manufacturer recommendations
• Allow adhesive to set fully before reconnecting power or using the appliance

The Float Mounting Tube O Ring is an OEM component specifically designed for GE dishwashers. This float mounting tube o-ring creates a watertight seal around a tube that helps monitor water levels using a float and switch assembly.  

Causes of a bad float mounting tube o-ring can include cracks, tears or warping that prevents proper sealing. Chemical exposure from regular dishwasher use can cause o-rings to degrade over time.

Symptoms of a bad Float Mounting Tube O Ring include:

• Water leaks in the area around the tube fitting  
• Moisture or water damage near water level monitoring components
• Irregular or improperly timed cycles from inaccurate water level readings
• Safety issues from undetected pooling or overflow of water

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This vent adapter connects a dryer's exhaust outlet to the home vent duct, restoring a secure exhaust path and helping maintain proper airflow for efficient drying. Durable construction resists cracking and air leaks at the connection. What it does:

• Provides a secure transition between the dryer exhaust and the vent duct to prevent air leakage
• Helps restore proper airflow to improve drying performance and reduce run times
• Replaces cracked, broken, or loose outlet adapters that can allow lint or moisture escape
• Keeps the exhaust pathway sealed to reduce noise and vibration at the connection

• Disconnect power to the appliance before starting any work; for gas dryers, turn off the gas supply as well
• Remove the old adapter and clean lint from the exhaust outlet and duct before installing the new adapter
• Use appropriate clamps or fasteners to secure the adapter and the vent duct per manufacturer instructions