Gdtp180ed0ww Parts

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This manual floor plate is the replacement cover that mounts at the appliance base to protect internal components and provide a finished surface. It restores the dryer's base appearance and helps prevent debris from entering the cabinet. What it does:

• Covers and protects the lower cabinet opening and components from dust and lint
• Helps maintain proper clearance and a finished look at the dryer base
• Replaces damaged, bent, or missing base plates that allow debris entry
• Can reduce rattles or vibration caused by a loose or warped floor plate

• One floor plate

• Disconnect power (and gas, if applicable) before servicing to avoid shock or injury
• Remove the dryer front or lower access panel per manufacturer instructions to access mounting screws
• Use correct-size screws and tighten to manufacturer torque; avoid over-bending the plate during installation

Left side roller cover.

The User Interface Housing is an OEM replacement part for GE dishwashers. Located at the front of the console, it houses the control panel responsible for cycle/option navigation.

The housing protects sensitive electronic components from water damage and physical impact. Its sturdy construction allows for responsive touch inputs without flex or play in the assembly. 

Symptoms of a bad user interface housing include:

• Warping or cracks exposing circuitry to damage
• Faulty sealing allowing moisture penetration
• Difficulty registering button presses from structural defects
• Ill-fitting installation negatively impacting usability

Causes can be repetitive openings allowing entry of dirt/moisture into critical areas and use over the years breaking down seals and weakening materials.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This adjustable toe kick replaces a damaged or missing front kick plate to restore a finished look and help protect the appliance base. It adjusts to fit and provides a clean, secure lower trim for the cabinet front. What it does:

• Covers and protects the appliance base from scuffs and debris
• Adjusts for a proper fit when original toe kick is warped or misaligned
• Helps stabilize the lower front trim and maintain a finished appearance
• Commonly used when the original toe kick is cracked, bent, or missing

• Basic hand tools may be required; keep fasteners from the original part for reinstallation if reusable
• Turn off and unplug the appliance before starting work and pull unit forward only as needed for access
• Handle edges carefully to avoid cuts; wear gloves if needed
• If mounting holes or clips are damaged, inspect for broken retainers and replace as necessary

This white console cover and graphic assembly replaces a worn or damaged control console face to restore the appliance's appearance and user markings. It provides the visible bezel and printed control labels for the machine's control area. What it does:

• Covers and protects the control board area while displaying the control graphics and labels
• Restores faded, scratched or cracked console appearance for clearer button/setting identification
• Helps keep dirt and moisture away from underlying controls and switches
• Addresses issues where damaged graphics make controls hard to read

• Disconnect power before beginning work to avoid shock or injury
• Typically secures with clips and/or screws; keep hardware for reassembly or replace as needed
• Handle the printed surface carefully to avoid scratching or removing graphics
• Fit and alignment before tightening fasteners

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

A white plastic tub trim that restores the washer's front appearance and helps seal the gap between the outer cabinet and inner tub. Replaces worn or cracked trim to improve fit and finish. What it does:

• Covers and protects the tub edge, providing a finished look around the washer opening
• Helps maintain a snug seal between the tub and cabinet trim to reduce snagging and debris buildup
• Common replacement for cracked, warped, or discolored trim that affects appearance or clearance
• Matches factory finish and mounting locations for a correct, secure fit

• One tub trim (white)

• Turn off and unplug the appliance before beginning any repair
• Removal typically requires opening the access panel or unhooking clips; handle trim gently to avoid snapping mounting tabs
• Keep mounting hardware and clips; reuse if undamaged or replace with manufacturer parts

This airbreak flow meter assembly detects water flow and helps the appliance manage fill and dispense cycles for reliable operation. It replaces a failing flow sensor to restore correct water-sensing and cycle control. What it does:

• Measures water flow through the system so the control can confirm proper filling
• Helps prevent overfill or underfill conditions by reporting flow status to the control
• Common symptoms of a failing unit: long or no-fill cycles, water-related error codes, or the appliance not advancing through cycles
• Works as part of the water/ice/fill system to ensure timing and valve operation respond correctly

• Disconnect power and shut off the water supply before starting any repair
• Handle the sensor and electrical connector carefully; avoid pulling on wiring
• Install in the correct orientation and ensure all seals and fittings are seated to prevent leaks
• After installation, restore power/water and run a test cycle to verify proper operation

This replacement console is the outer control panel that houses the user controls and provides the finished front for your appliance. Restores proper button access and a clean, functional appearance. What it does:

• Replaces a cracked, warped or damaged control panel that prevents button access or looks worn
• Provides the mounting surface for switches, knobs and displays so controls operate correctly
• Helps stop drafts or moisture from entering the control cavity through damaged trim
• Restores a neat, factory appearance to the appliance front

• One console

• Unplug the appliance before starting to avoid shock or injury
• Removal typically requires taking off trim pieces, knobs or fascia screws—keep fasteners for reassembly
• Handle carefully to avoid scratching or cracking the new panel during installation

This wash pump discharge hose routes water from the washer's pump to the drain path, helping remove wash water during drain cycles. Replaces a cracked, split or clogged discharge hose to restore proper draining. What it does:

• Carries pump discharge water from the wash pump to the drain outlet
• Prevents leaks caused by cracks, splits or brittle sections in the original hose
• Helps stop water pooling or slow draining when the hose is damaged or disconnected
• Matches OEM shape and connection points for a direct replacement

• Disconnect power and water supply before starting any repair.
• Inspect pump outlet and drain fittings for damage; replace clamps if rusted or worn.

This rail and end cap assembly secures a refrigerator shelf or door bin and restores a stable mounting surface for stored items. It replaces worn or damaged rails that allow shelves to sag or detach. What it does

• Replaces a damaged shelf rail and end cap to restore proper shelf support
• Holds the shelf/bin in position so items stay level and don't slide off
• Stops rattling or movement caused by a loose or broken rail assembly
• Fits where an original molded rail/end cap has cracked, worn, or failed

• One rail and end cap assembly as shown

• Remove food and bins from the area before starting; support the shelf while removing the old part
• Use basic hand tools; avoid forcing parts — align tabs and slide the rail into place until it snaps or seats
• Disconnect power if required by your model before working near electrical components

This latch cam engages the door latch mechanism so the appliance door closes and stays secure during cycles. A worn or broken cam can prevent the door from latching or cause the door to feel loose. What it does

• Rotates with the latch to lock the door securely during operation
• Ensures the latch striker catches and holds the door closed
• Common symptom: door won't stay latched or appliance won't start
• Common symptom: door feels loose, noisy, or intermittently opens during cycles

• One latch cam

• Disconnect power before starting any repair to avoid shock or injury
• Inspect surrounding latch components and replace any visibly damaged parts
• Use basic hand tools; keep track of small fasteners and alignment during reassembly
• Test door operation several times after installation to ensure secure engagement