Gdtp180ed0ww Parts

This middle spray arm conduit assembly restores proper water delivery to the dishwasher's middle level. It channels wash water to the mid arm and rotates to improve coverage on the upper rack for consistent, reliable cleaning.

• Routes water from the pump to the middle spray arm to wash items on the upper rack
• Spins and sprays through jet holes for even coverage
• Replaces cracked, warped, or clogged assemblies that hinder rotation or spray
• Typical symptoms include poor cleaning on the upper rack, the mid arm not spinning, or visible damage/clogs

• Disconnect power and water supply before servicing
• Pull out the upper rack; release the rear coupling/retainer and any tabs or clips to remove the old assembly
• Fully seat the new assembly into the rear water supply port; ensure the spray arm spins freely
• Run a short test cycle to check for leaks

The Rack Bracket - 2 Wheels is an OEM part for GE dishwashers. It supports and allows the smooth movement of the dishwasher rack in and out of the machine, providing stability and ease of use during loading and unloading.

Causes of a bad rack bracket can include wear and tear from regular use, accumulation of debris or hard water deposits, or physical damage from overloading or mishandling the rack.

Symptoms of a bad rack bracket include:

• Difficulty sliding the rack in and out
• The rack derailing or not staying in place
• Unusual noises during rack movement
• Visible damage to the bracket or wheels

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This right-hand rack slide and end cap assembly guides and retains the dishwasher rack on its track. Replacing a worn assembly restores smooth rack travel and helps prevent the rack from over-extending or dropping on the right side.

• Provides the right-side slide track for the dishrack and includes the built-in end-cap stop
• Maintains rack alignment for smooth in-and-out movement
• Replace if the slide is bent or the stop/end cap is cracked or missing
• Typical symptoms include the rack falling off the track, over-extending, binding, or sitting unevenly on the right side

• Disconnect power at the breaker and turn off water if moving the appliance for access
• Pull the rack out; support it before removing the existing slide
• Remove any mounting screws or release locking tabs to detach the old slide; transfer hardware if required
• Position and secure the new right-hand slide; ensure the end cap locks, then test rack travel

The UI Control Assembly is an OEM part for GE dishwashers. It manages all the electronics and user interface components on the control panel. This assembly includes the control board that directs water temperature, wash cycles, and more based on user selections. 

Causes of a bad UI Control Assembly can include water damage from leaks, failure of electronic components over time, or issues with the control panel buttons or display. 

Symptoms of a bad UI Control Assembly include:

• The dishwasher not starting or not responding to selections
• Inability to change settings or cycles 
• Error codes appearing on the display
• Unresponsive or non-functioning buttons

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Keep your dishwasher's pump protected. This glass trap sits in the sump and captures broken glass and large debris before it reaches the wash motor and spray system, helping maintain water flow and consistent cleaning performance.

• Traps shards and hard debris in the sump to protect the wash motor and pump
• Helps maintain proper water circulation and spray pressure
• A clogged or damaged trap can cause poor cleaning or grit left on dishes
• Grinding or rattling from the sump area may indicate debris in a compromised trap
• If the trap won't seat or lock, debris can bypass filtration

• Disconnect power and water; wear cut-resistant gloves to handle broken glass and sharp debris
• Remove the lower rack and, the lower spray arm; unlock and lift out the old trap
• Clear all debris from the sump; inspect sealing surfaces and nearby filter components
• Seat the new trap fully and lock it in place; reassemble and run a quick test for proper operation

The Mid Spray Arm and Gasket Assembly is an OEM replacement part for GE dishwashers. It refers to the horizontal rotating component above the lower rack that provides mid-level spray coverage. Over many cycles of use, seals, and joints can harden.

Symptoms of a bad mid-spray arm assembly include: 

• Water leaks inside the dishwasher tub from dried-out or cracked mounting gaskets
• Difficult rotation indicating worn bearings or corroded fasteners  
• Impeded spray patterns with diminished cleaning on rack shelves

Causes leading to failure are typically repetitive motions stressing connections combined with seal exposure to heat and chemicals causing deterioration.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This replacement O-Ring restores a watertight seal at an internal dishwasher connection, helping stop leaks and protect surrounding cabinetry. Replace a hardened, cracked, or flattened seal to maintain reliable wash performance and prevent water damage.

• Creates a watertight seal between mating parts inside the dishwasher
• Helps prevent drips and leaks during fill, wash, and drain cycles
• Addresses leaks caused by a worn, flattened, or damaged seal
• Visual clues: cracks, brittleness, deformation, or mineral trails at the joint

• Disconnect power and shut off the water supply before servicing
• Access the affected connection and remove the old O-ring
• Clean the groove and mating surfaces; lightly lubricate with food-grade silicone grease; seat evenly without twisting or pinching
• Reassemble and run a brief test cycle to check for leaks

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

This fill funnel assembly mounts inside the dishwasher tub at the water inlet. It directs incoming water into the tub and helps prevent splashing or leaks at the fill area for reliable fills and cleaner operation.

• Channels water from the inlet opening directly into the tub
• Helps control splash and seal the fill port to reduce drips
• Damage, cracks, or a missing funnel can cause leaks near the fill area during the fill cycle or unusual spraying sounds
• Restores proper water entry path for consistent filling

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the fill inlet on the tub wall
• Remove retaining fastener(s) or tabs, replace the funnel, and ensure any seal is properly seated
• Reassemble and run a brief fill/rinse to check for leaks at the inlet area

The Funnel Service Kit is an OEM replacement part for GE dishwashers. It includes a water inlet funnel and seals necessary for proper water flow within your dishwasher. This part helps prevent leaks and ensures that water is properly directed into the dishwasher.

Symptoms of a faulty water inlet funnel service kit include:

• Water leaks from the dishwasher
• Insufficient water flow during the wash cycle
• Inconsistent cleaning or rinsing performance

Causes of a bad water inlet funnel service kit can include wear and tear over time, blockage from debris or mineral buildup, or damage to the funnel or associated components. If you notice issues such as water leaks, inadequate water flow, or inconsistent cleaning results, it may be time to replace the old or damaged water inlet funnel service kit with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This pump isolator hanger secures and cushions the dishwasher's pump assembly, helping reduce vibration and noise while keeping the pump properly supported. Replacing a worn hanger restores stable, quieter operation and maintains correct pump alignment.

• Supports and isolates the pump assembly beneath the tub to dampen vibration
• Helps keep the pump properly positioned and prevents contact/rattling
• Replace if the hanger is stretched, cracked, or broken
• Common symptoms include louder operation, rattling from the base, or a sagging pump assembly

• Disconnect power and shut off water before servicing; wear gloves and eye protection
• Access from the front base by removing the toe-kick/kickplate; support the pump assembly
• Detach the worn hanger from its mounting points and install the new hanger in the same locations
• Ensure the pump is secure, hoses/wires aren't strained, and run a brief test for noise/vibration

This heater nut secures the dishwasher's heating element where it passes through the tub, helping maintain a tight connection and proper positioning. Replacing a damaged or missing nut can help prevent leaks and keep the element stable.

• Fastens the heating element to the tub from below to hold it firmly in place
• Helps support a watertight connection at the element pass-through when used with the proper seal
• Replace if the nut is cracked, heat-damaged, stripped, or missing
• Common symptoms include water leaking under the unit near the heater terminals and a loose or wobbly heating element

• Disconnect power at the breaker and shut off water before servicing
• Access the nut from beneath the dishwasher; remove the toe-kick and pull the unit forward if needed
• Support the element from inside the tub while tightening; snug gently and do not overtighten to avoid damage
• Restore power/water and run a short cycle to check for leaks