Ge Cfcp1nizess Parts

This divider pan separates and supports crisper drawers to help keep produce organized and contained. It restores the original divider function so drawers slide and seal correctly, reducing shifts and spills inside the refrigerator. What it does

• Replaces a broken or missing divider that separates crisper drawers or pans
• Helps keep fruits and vegetables organized and contained to prevent mixing
• Supports proper drawer alignment and reduces unwanted movement or rattling
• Can stop small spills from spreading across the crisper area

• One divider pan

• Removal/installation is user-serviceable on most units; remove produce and gently lift or slide the old divider out before fitting the replacement
• Inspect surrounding rails and clips for damage; replace if worn to ensure proper fit
• Use gloves to avoid sharp sheet-metal edges and keep components clean during install

This replacement front pan cover gasket seals the refrigerator evaporator/drip pan area to help control moisture and direct defrost water into the drain. Restores a proper seal to reduce leaks and moisture buildup under the pan. What it does:

• Seals the front edge of the evaporator/drip pan to prevent water from escaping the pan area
• Helps route defrost and condensation into the drain system to avoid pooling
• Reduces moisture accumulation that can cause odors or frozen drainage
• Commonly replaced when old gasket is cracked, hardened, or missing

• One front pan cover gasket

• Inspect surrounding pan and trim for damage before installing; replace any broken clips or retainers
• Clean mating surfaces and remove debris to ensure a full seal
• Gasket typically presses into a channel or secures with clips—no special tools required, but a flat tool can assist seating
• Disconnect power to the appliance before servicing to avoid electrical hazard

This condenser shroud is the plastic cover that protects and channels airflow around the refrigerator condenser, helping the cooling system run efficiently and keeping components shielded from debris. What it does:

• Directs airflow over the condenser coils to help dissipate heat
• Protects condenser and nearby components from dust, pet hair, and accidental contact
• Helps maintain proper clearance and airflow paths behind the fridge
• Can reduce vibration noise by stabilizing condenser area

• One condenser shroud/cover

• Designed to mount in the condenser compartment; follow your model's service manual for correct orientation and fasteners
• Disconnect power to the appliance before accessing the condenser area to avoid electrical shock
• Inspect and clean condenser coils while the shroud is removed for best performance
• If clips or screws are damaged, replace them with OEM-recommended hardware

This slide-out lower basket replaces a worn or damaged refrigerator lower storage basket to restore organized storage and easy access to fresh foods. Durable molded construction keeps produce contained and visible. What it does

• Provides a removable lower storage basket for organizing fruits, vegetables, and deli items
• Slides out for easy access so you can reach items at the back without lifting
• Replaces cracked, broken, or warped baskets that no longer support contents
• Helps keep refrigerator interior tidy and prevents items from rolling around

• One lower slide-out basket

• Snap or slide into the existing lower track; matches original mounting points
• Remove all food and use caution when handling edges to avoid pinching
• Inspect tracks and glides for damage; replace glide parts separately if basket does not slide smoothly
• Disconnect power only when performing additional repairs nearby

This adjustable hinge pin replaces a worn or damaged door hinge pin to restore proper door alignment and smooth opening. Simple replacement helps stop door sag, uneven gaps, and rubbing during use. What it does

• Provides the pivot point for the appliance door so it opens and closes smoothly
• Allows adjustment to correct door height and alignment after wear or impact
• Helps eliminate door sag, uneven sealing, or contact with cabinet/frame
• Restores consistent door operation and reduces binding or scraping noises

• One adjustable hinge pin

• Disconnect power and empty/support the door before removing hinge components for safety
• Support the door while replacing the hinge pin to prevent dropping or damage
• Reinstall fasteners securely and verify correct alignment before fully tightening
• Test door operation and seal after installation; adjust as needed

This replacement corner cap restores the finished edge and protective cover on an oven door corner for a clean appearance and proper fit. It replaces a cracked, chipped, or missing corner that can catch debris or show damage. What it does:

• Covers and protects the outer corner of the oven door from chips and dents
• Helps maintain a smooth door edge so the door closes and seals properly
• Improves cosmetic appearance when the original corner is cracked or worn
• Reduces sharp or rough edges that can catch on clothing or cause minor cuts

• Turn off power to the appliance and allow the oven to cool before servicing
• Installation may require partially removing the oven door or trim; have basic hand tools ready
• Handle the door and trim carefully to avoid scratching finished surfaces

This main board enclosure houses and protects the appliance's electronic control board, keeping wiring and circuitry secure and organized for reliable operation. It helps prevent contact damage and contains the control components in one location. What it does:

• Covers and protects the main electronic control board from debris and accidental contact
• Keeps wiring routed and secured around the control area to reduce strain on connectors
• Helps maintain correct positioning of the control board for consistent electrical connections
• Useful when the original housing is cracked, missing mounting points, or allowing exposed circuitry

• Disconnect power to the appliance before beginning any work to avoid shock or damage
• Handle the control board and connectors gently; avoid touching circuit traces or components
• Keep track of any mounting screws and brackets removed during disassembly for reinstallation