Ge Cfe29tsdcss Parts

This hinge cap is the small trim piece that covers your refrigerator door hinge. Replacing a cracked or missing cap protects the hinge from dust and restores a clean, finished look to the door area.

• Covers and protects the door hinge hardware from dust and debris
• Restores a clean, factory-finished appearance
• Helps keep the hinge area clear for smooth door movement
• Replace when the original cap is cracked, loose, discolored, or missing

• Disconnect power before servicing the appliance
• Support the door to prevent movement while working near the hinge
• Remove the old cap; align and press the new cap onto the hinge until fully seated; reuse the original fastener if your model uses one
• Verify the cap is secure and does not rub as the door opens/closes

This hinge center assembly replaces the refrigerator's right-side hinge pivot to restore proper door alignment and smooth opening. It helps reduce door sag and improves sealing for better performance. What it does:

• Provides the central pivot point for the right refrigerator door hinge
• Restores correct door alignment and even closing when the door is sagging or crooked
• Reduces rubbing, binding, or grinding noises from the hinge area
• Helps maintain an effective door seal to prevent cold air loss

• One hinge center assembly (right side)

• Unplug the appliance and empty or support the door before starting work
• Support or brace the door while removing hinge fasteners to prevent dropping
• Reuse existing screws/bolts unless new hardware is specified by the manufacturer

This grill recess is a molded trim piece that restores the recessed area at the front lower grille of the refrigerator, helping the grille sit flush and improving appearance. It replaces damaged or missing trim for a clean, finished look. What it does:

• Provides the recessed mounting/trim area that the lower grille fits into
• Secures and stabilizes the grille so it sits flush with the cabinet face
• Covers rough or damaged cabinet edges for a finished appearance
• Reduces rattling or movement caused by a loose or broken trim piece

• Disconnect power to the appliance before starting any repair
• Typically installs by aligning and snapping or fastening into existing mounting points
• Use basic hand tools as needed; avoid forcing the plastic to prevent breakage
• Replace damaged clips or fasteners to ensure a secure fit

This door case wiring harness connects the refrigerator door components to the main cabinet harness, restoring reliable power and signal routing for lights, dispensers, and sensors. Replaces a damaged or frayed harness to help resolve intermittent or non-working door functions. What it does:

• Transfers power and control signals between the door and cabinet wiring
• Restores operation for door-mounted lights, dispensers, and sensors affected by broken wiring
• Prevents shorts or intermittent failures caused by frayed or pinched wires
• Matches OEM routing and connector locations for a direct-replacement fit

• One door case wiring harness

• Disconnect power to the appliance before starting work to avoid shock or injury
• Handle connectors gently and route wiring per cabinet clips to avoid pinching
• Verify connector orientation and seating; secure any retained clips or screws

The Pcb Asm Humidity Board is an OEM part for GE refrigerators. This humidity control board regulates the humidity levels within the refrigerator's crispers or drawers. It allows you to adjust and maintain the ideal humidity level for different types of produce, extending their shelf life and preserving their quality.

Symptoms of a bad humidity control board include:

• Inconsistent humidity levels
• Excessive moisture buildup
• Rapid spoilage of produce

A bad humidity control board can occur due to electrical issues, component failure, or other factors. If you notice symptoms such as inconsistent humidity levels, excessive moisture buildup, or produce spoiling quickly, it may be time to replace the humidity control board.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

This display cover is the clear outer lens that protects and reveals the refrigerator control panel so buttons and indicators stay visible and damage-free. It restores a finished appearance and keeps the controls readable. What it does:

• Protects the control board and display from spills, dust, and everyday wear
• Keeps touchpads, LEDs and indicator icons visible and readable
• Helps maintain a clean, factory appearance on the console
• Can prevent dirt from entering gaps that cause sticky or unresponsive buttons

• For most installs remove power to the appliance before starting (unplug or switch off breaker)
• Typically installs by snapping or fastening into the console; handle gently to avoid cracking
• Keep screws and clips from the old cover for reuse if matching; replace damaged clips
• If the underlying display or electronics are damaged, replace or inspect those parts separately

This power cord harness routes mains power from the wall to the appliance, restoring a secure electrical connection for reliable operation. It replaces a damaged or worn inlet harness to help eliminate power loss and poor contact. What it does:

• Carries incoming AC power from the appliance inlet to internal wiring and control components
• Replaces frayed, melted, or broken cord connections that can cause loss of power
• Can resolve symptoms like the appliance not powering on, intermittent power, or tripping a breaker
• Restores a firm, strain-relieved connection at the power inlet to reduce arcing and overheating risk

• Disconnect power at the breaker or unplug the appliance before beginning any work
• Installation requires basic hand tools and access to the appliance's rear or service panel
• Inspect mating connectors and strain reliefs; replace if damaged
• If you see burn marks, melted insulation, or exposed conductors, replace the harness and verify inlet integrity

This replacement icebox door gasket creates an airtight seal around the freezer/icebox door to help maintain proper temperature, reduce frost buildup, and keep stored food fresher longer. What it does:

• Seals the icebox/freezer door to prevent warm air intrusion and moisture entry
• Helps reduce frost and ice buildup inside the compartment
• Supports consistent compartment temperature for better food preservation
• Can improve cooling efficiency when gasket is worn or damaged

• One icebox/ice compartment door gasket

• Remove the old gasket and clean the door gasket channel before installing the new seal
• Align the gasket evenly around the door and press into the channel; work from one corner and go around the door
• Avoid sharp tools that could damage the new gasket; if needed, warm the gasket slightly for flexibility per OEM guidance
• Check for an even, continuous seal after installation and adjust as needed

This left-side lower freezer slide restores smooth drawer movement and proper alignment in the freezer compartment. It replaces a worn or damaged slide to help the drawer open and close reliably. What it does:

• Replaces the left lower freezer drawer slide that guides the drawer on its track
• Restores smooth, even sliding and prevents the drawer from sticking or binding
• Helps keep the drawer properly aligned so it opens and closes without catching
• Useful when the existing slide is bent, cracked, or worn and affects drawer operation

• Disconnect power and remove food from the drawer area before starting
• Typically installs onto the freezer cabinet and drawer track; basic hand tools may be required
• Align slide with factory mounting points and secure hardware; test drawer movement after installation

Size: 8 - 18 ab.

This is a replacement round-head screw sized 10-24 x 5/8 in. It secures trim, panels, and internal components so parts stay aligned and appliances run quietly and safely. What it does

• Fastens panels, brackets, and trim pieces in place
• Prevents loose parts that can rattle or cause misalignment
• Replaces missing or stripped screws to restore secure mounting
• Works where a 10-24 x 5/8 round-head screw is required

• Disconnect power before servicing the appliance
• Use the proper screwdriver or nut driver to avoid stripping the head
• Align parts before tightening and thread gently to avoid cross-threading
• Do not over-tighten; stop when snug to prevent panel distortion

This 1/4-20 hex washer head screw secures panels and components in place, restoring proper fit and eliminating movement. It fits common appliance assemblies that use a 7/8" long, 1/4-20 threaded fastener. What it does:

• Fastens panels, brackets, and assemblies that use a 1/4-20 thread
• Restores secure fit when original screw is missing, stripped, or loose
• Helps stop rattling, vibration, and misalignment caused by loose hardware
• Matches common OEM head style for tool-ready installation with a socket or wrench

• Disconnect power to the appliance before servicing where applicable
• Use the correct 1/4-20 socket or wrench; install hand-tight then snug—do not overtighten
• Replace like-for-like: head style, thread size, and length before installing
• If fastener holes or threads are damaged, repair or retap before reuse

This clutch coupling connects the washer motor/clutch to the agitator so the tub agitates properly during the wash cycle. Replaces a worn or broken coupling to restore normal agitation and reduce slipping or grinding. What it does:

• Transfers motor/clutch rotation to the agitator so clothes move during wash cycles.
• Commonly used when the washer spins but does not agitate or when agitation is weak.
• Helps eliminate slipping, grinding, or unusual noise from a failing coupling.
• Works as the mechanical link between the drive system and agitator assembly.

• One clutch coupling as pictured and specified by the OEM.

• Disconnect power and water supply before starting any repair.
• Basic mechanical skills and common hand tools required; follow OEM disassembly steps for safe access.
• Inspect related parts (agitator, drive shaft, clutch) for wear and replace as needed.

This LED light shield protects and diffuses the refrigerator's LED lighting, restoring even illumination and preventing direct exposure to the lamp. Replace a cracked, yellowed, or missing shield to improve light distribution and appearance. What it does:

• Covers and protects the LED light assembly from damage and debris.
• Diffuses LED output for softer, more even interior lighting.
• Replace if the shield is cracked, broken, warped, or discolored.
• Helps prevent direct glare from exposed LEDs for safer visibility.

• One LED light shield / cover.

• Disconnect power to the appliance before starting any work.
• Handle the shield carefully—plastic can crack; avoid overtightening fasteners.
• Install by aligning with existing mounting points or clips; do not force into place.
• Inspect the LED module and wiring.