Ge Gdt580ssf4ss Parts

This 10-32 x 9/16 machine screw secures dishwasher components and panels. Replacing a missing or stripped fastener restores a tight fit, reduces vibration/rattles, and keeps assemblies properly aligned for reliable operation.

• Secures panels, brackets, or internal assemblies using a 10-32 machine thread
• Replaces lost, corroded, or stripped screws
• Can help resolve looseness or rattling from a loose mounting point
• Correct 9/16-inch length helps maintain proper spacing and alignment

• Disconnect power at the breaker before servicing
• Use the appropriate driver for the screw head; start threads by hand to avoid cross-threading
• Tighten snugly but do not overtighten to prevent stripping threads or damaging mating parts
• Compare to the original fastener to matching thread and length

• Thread size: 10-32
• Length: 9/16 inch

This replacement upper spray arm assembly restores full wash coverage to the top of your dishwasher. It spins under water pressure, directing jets across the racks so dishes come out cleaner with fewer spots and leftover food.

• Distributes pressurized water through its jets to clean the upper section
• Replaces a spray arm that is cracked, warped, clogged, or not rotating freely
• Typical symptoms: poor cleaning on the top rack, residue left on dishes, or rattling from the arm striking items
• Restores even spray coverage when properly installed and unobstructed

• Disconnect power and water supply before servicing
• Release and remove the old upper arm (tab/clip/retainer varies by model); clear debris from the hub/feed area and transfer any reusable hardware
• Seat the new arm fully and confirm it spins freely before restoring service

This dishwasher main control board kit is the central circuit board that directs all wash functions. Replacing a failed board restores proper power distribution and timing so cycles start, advance, and finish correctly, helping prevent intermittent shutdowns and erratic operation. What it does:

• Controls cycle timing and communicates with sensors
• Distributes power to the wash motor, drain pump, inlet valve, and heater
• Works with the door latch and user interface to start/stop the cycle
• Failure may cause no power/won't start, stalled cycles, blinking lights/error codes, or incorrect filling, draining, or heating

• One main control board kit

• Disconnect power at the circuit breaker; turn off water if moving the dishwasher for access
• Board is typically in a housing beneath the unit—use ESD precautions and keep connections dry
• Photograph/label wire harnesses; transfer connectors one at a time to the new board
• Restore power and run a test or rinse cycle to proper operation

This leveling leg adjusts the dishwasher's height at the base, helping you level and stabilize the unit inside the cabinet. Proper leveling reduces rocking and vibration and promotes a tight door seal and smooth rack operation.

• Screws into the base frame to set height and level the dishwasher
• Supports the unit to prevent rocking or wobbling
• Helps maintain door alignment and sealing; poor leveling can contribute to leaks
• A worn, bent, or missing leg can make leveling difficult and increase vibration/noise

• Disconnect power and shut off water; slide the dishwasher out if needed for access
• Turn the leg with a wrench or pliers to adjust height; replace by threading the new leg into the base
• Use a bubble level to set side-to-side and front-to-back level before re-securing the unit
• Do not overtighten; ensure both legs carry weight evenly on a solid floor surface

The Vent Filter is an OEM part for GE dishwashers. It helps to capture and filter out food particles, grease, and other debris. 

Causes of a bad vent filter can include clogging or blockage due to accumulated debris, wear and tear over time, or damage to the filter material.

Symptoms of a bad vent filter include:

• Lingering unpleasant odors during or after the dishwasher cycle
• Visible signs of debris or buildup on the filter surface
• Reduced effectiveness of the dishwasher's drying performance

Replace your worn-out or clogged vent filter with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This tub insulation is the replacement foam/fiber wrap that lines the dryer drum area to help retain heat, reduce exterior cabinet temperature, and dampen operation noise for more efficient, quieter drying. What it does:

• Wraps around the dryer drum/tub to help limit heat loss during cycles
• Helps reduce cabinet surface temperature for safer operation
• Dampens vibration and operating noise from the rotating drum
• Supports consistent drying performance by improving heat retention
• Useful when original insulation is damaged, torn, or missing

• Disconnect power (and gas supply for gas dryers) before servicing
• Access requires removing the dryer cabinet or drum per OEM instructions
• Handle carefully—use gloves and eye protection; avoid breathing any loose fibers
• Reinstall with original fasteners and seal as needed to maintain drum clearance

This dishwasher junction box cover encloses the power-connection compartment at the base of the unit. Replacing a damaged or missing cover helps protect wiring from debris and accidental contact, restoring a safe, secure connection area. What it does:

• Covers and secures the dishwasher's electrical junction box
• Helps shield wire splices from moisture, dust, and accidental contact
• Restores proper fit when the original cover is cracked, broken, or missing
• Useful if the junction box won't stay closed or the cover no longer secures properly

• Includes 1 junction box cover

• Disconnect power at the circuit breaker before servicing
• Remove the lower access/kick panel to reach the junction box
• Remove the old cover and screw, position the new cover, and secure with the existing hardware
• Ensure all wiring and the strain relief are fully inside the box before closing; restore power and test

This adapter plate is a molded interface in the wash system that secures and seals components so water pressure is routed correctly. Replacing a cracked or warped plate helps stop leaks and restore proper spray performance.

• Connects and supports wash-system components at the sump/water-feed interface
• Maintains a reliable seal to help prevent leaks
• Helps direct wash water to the spray arms for effective cleaning
• Replace if cracked, warped, or stripped; symptoms can include leaks, weak spray, or a loose spray arm

• Disconnect power and water supply before servicing
• Remove the lower rack and related wash components to access the plate; note the order of parts for reassembly
• Reuse existing seals and fasteners in their original positions; seat the plate evenly and tighten hardware snugly, not overtight
• Run a brief test cycle and inspect for leaks before full use

This conduit seal fits the dishwasher's water-feed conduit connection, keeping wash water contained and pressure steady to the spray arms. Replacing a worn seal helps address leaks and maintain reliable cleaning performance.

• Seals the joint where the dishwasher's water feed conduit/tube connects within the wash system
• Helps prevent water leaks at the conduit connection point
• Maintains proper wash pressure for consistent spray performance
• Common signs of failure: drips beneath the unit, visible cracks/flattening, or a loose-fitting old seal

• Disconnect power and shut off the water supply before servicing
• Access the conduit connection (location varies by model), remove the old seal, and clean mating surfaces
• Lightly moisten the new seal to ease installation and seat it fully
• Reassemble and run a brief cycle to check for leaks

The Upper Spray Arm Support is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper spray arm, and is responsible for securely mounting and holding the upper spray arm in place during operation.

Symptoms of a bad upper spray arm support include:

• Vibration or noise from an unsecured spray arm
• Improper alignment of water spray pattern  
•  Restricted rotation of the spray arm during washing
• Leaks at the tub connection point

Causes of a bad spray arm support can be from cracks or breaks that compromise its structure, or wear over extended use without replacement. 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher fill hose routes incoming water from the inlet valve into the tub. Replacing a brittle or leaking hose helps restore proper filling and reduces the risk of water leaks under the unit.

• Carries fresh water from the inlet valve to the dishwasher during the fill cycle
• Helps maintain correct water level for reliable wash performance
• Common symptoms of a failed hose: leaks near the toe kick, slow fill, or no fill
• Replaces hoses that are cracked, swollen, kinked, or deteriorated

• Disconnect power and shut off the water supply before service
• Place a towel or shallow pan to catch residual water
• Access behind the lower kick panel; transfer existing clamps/fittings as needed
• Route the hose without kinks, fully seat connections, restore water, and check for leaks during a test cycle

The Turbidity Sensor Assembly is an OEM part for GE dishwashers. It is responsible for monitoring the cleanliness of the water during the dishwashing cycle. The turbidity sensor measures the level of particles and impurities in the water, allowing the dishwasher to adjust the cycle accordingly. It helps prevent issues such as over-washing or under-washing, resulting in clean dishes every time.

A bad Turbidity Sensor Assembly can lead to improper cleaning performance or cycle errors. Causes of a bad turbidity sensor can include sensor malfunction, damage to the sensor, or buildup of residue affecting its accuracy.

Symptoms of a bad Turbidity Sensor Assembly include:

• Incomplete or inadequate cleaning of dishes
• Error codes related to water cleanliness or turbidity
• Extended or shortened cycle times without reason
• Persistent residue or film on dishes after the cycle

Replace your faulty or damaged Turbidity Sensor Assembly with this genuine OEM GE part to ensure precise cleaning performance and spotless results. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available