Ge Jgbs30dek2ww Parts

Size: 8 - 32 inch.

A sealed rocker switch that replaces a failed control rocker on appliance panels to restore reliable on/off switching. Designed for direct-fit replacement of the original sealed rocker switch to help stop intermittent or non-working controls. What it does

• Provides user on/off control for the corresponding circuit or function on the appliance control panel.
• Sealed design helps resist moisture and grease common around cooking surfaces.
• Replaces worn, cracked, or unresponsive rocker mechanisms that cause inconsistent operation.
• Can resolve symptoms such as a switch that does not click, fails to make contact, or works only intermittently.

• One sealed rocker switch.

• Disconnect power to the appliance before beginning any repair to avoid shock hazard.
• Access usually requires removing the control panel or overlay—retain all screws and fasteners for reassembly.
• Match switch orientation and wiring connections exactly; note wire locations or take a photo before removal.
• Test function after reassembly and restore power only when panels and fasteners are securely replaced.

This small V2 inlet jet directs water flow to the dispenser/ice-making area so the appliance fills and forms properly. It restores correct water routing for consistent filling and helps reduce weak or misshapen ice or slow dispensing. What it does:

• Channels water to the ice maker/dispenser so the correct amount reaches the fill area.
• Helps ensure uniform ice formation and consistent dispenser flow.
• Can resolve symptoms like weak/slow dispensing, underfilled ice trays, or uneven ice cubes.
• Works as the small replacement nozzle where the original inlet jet is worn or blocked.

• One small V2 inlet jet

• Disconnect power and shut off the water supply before beginning work.
• Access may require removing inner panels or the ice maker/dispenser housing; follow your model's service instructions.
• Inspect the seat and surrounding fittings for debris or damage before installing; replace other damaged components as needed.

This is a replacement mounting screw for the refrigerator/freezer thermostat assembly. It secures the thermostat to the cabinet so temperature sensing and control remain stable and reliable. What it does:

• Secures the thermostat housing or bracket to the appliance cabinet
• Keeps the thermostat properly positioned for accurate temperature sensing
• Common fix when a loose, missing, or stripped thermostat fastener causes rattling or poor contact
• Small hardware part used during thermostat replacement or reassembly

• One thermostat mounting screw

• Turn off power to the appliance before starting any repair
• Use appropriate screwdriver and do not overtighten to avoid stripping the housing or threads
• If original hole or threads are damaged, inspect bracket or cabinet and replace as needed

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

The GE Range Support Base is an OEM replacement part for GE wall ovens and ranges. It provides critical support and stability for the appliance, ensuring safe and reliable operation. 

Causes of a bad support base could include cracks or breaks in the material over time due to repeated stresses and strains from the heavy appliance above it. The base may also become damaged or unstable if the unit is moved incorrectly and suffers impact.

Symptoms of a failing support base include:

• The oven or range rocking or becoming unlevel during use  
• Noisy or squeaking sounds coming from the base
• Visible cracks or weaknesses in the material
• The appliance seeming loose or unstable on the countertop or floor

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Package of 12

This broil handle clip secures the broiler door handle to the oven door, restoring a safe, solid grip and preventing the handle from slipping or detaching. It's a small replacement part that fixes loose or wobbly broiler handles. What it does:

• Holds the broil/door handle firmly in place so the handle doesn't move or fall off
• Addresses symptoms like a loose, wobbly, or partially detached broiler handle
• Matches OEM function and fit to maintain proper door operation
• Works with the existing handle and mounting hardware when undamaged

• One broil handle retaining clip (single clip as shown)

• Disconnect power to the appliance before beginning any repair
• Remove the oven door or access panel per the manufacturer instructions to reach the handle clip
• Reuse existing screws and handle hardware unless they are damaged; replace as needed

This contoured washer is a shaped fastening washer used on compatible GE top-load washers to secure and cushion mating parts. It helps maintain proper alignment and reduces wear where parts bear against each other. What it does

• Provides a contoured bearing surface to help distribute load and reduce point wear
• Cushions and isolates components to help limit vibration and noise
• Secures fasteners or assemblies in tight, shaped recesses
• Helps maintain correct part alignment for reliable operation

• One contoured washer

• Disconnect power to the washer before servicing to avoid shock or injury
• Use proper tools and observe orientation; tighten fasteners to manufacturer guidance

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

The GE Front Orifice Holder-Left is an OEM part for GE gas ranges. It secures the front left burner's gas orifice nozzle to properly regulate fuel delivery.

Symptoms of a bad front orifice holder include:  

• Burning or fire hazards if gas leaks around the holder's joint
• Inability to adjust the flame height or heat level on that burner  
• Uneven heating performance between the front left burner and others

Causes may include cracks, corrosion or material fatigue developing in the holder over many heating and cooling cycles. Mineral deposits could also potentially cause issues. 

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas ranges.

The Knob Thermostat Assembly is an OEM part for GE gas ranges. It allows for control of oven baking temperatures through the regulation of pilot lights and burners.

Symptoms of a bad knob thermostat assembly include:  

• Erratic or inaccurate temperature readings
• Difficulty selecting or maintaining desired heat levels
• Unstable or inconsistent baking performance   
• Improper ignition or control of range burners

Causes of a malfunctioning knob thermostat include continuous exposure to cooking heat and normal wear over extended use. The internal components experience constant adjustment and fluctuations that can lead to loosening or degradation over time.

This part works for some Hotpoint and RCA gas range models as well.

The Burner/Oven Assembly is an OEM part for GE gas ranges. It holds ignition and valve components over lower cooking surfaces. 

Causes of failure include deterioration of high-temperature seals from repeated heating cycles, stripped mounting points from frequent removal/cleaning access, and impact damage to housing structures.

Symptoms of a faulty burner/oven assembly are:

• Gas leaks around burner bases or control knobs
• Unstable or irregular flame sizes lacking responsiveness   
• Potential safety hazards from exposed connections or cracks 

This OEM part is compatible with Hotpoint and RCA gas range models as well.

The Burner Box Harness is an OEM part for GE gas ranges. It connects burners and heating elements to power and modulation controls.  

Symptoms of a bad burner box harness include:

• Inability to select bake/broil functions or heating levels 
• Faulty or unresponsive oven/burner temperature knobs 
• Intermittent or unstable heating performance from areas

Causes involve wire degradation from long-term ambient heat, cuts from sharp surfaces, or loose connections that compromise conductivity. 

This OEM part is also compatible with Hotpoint and RCA electric range models.

This replacement white door handle restores a firm grip and original appearance to compatible appliances. It's a direct-fit exterior handle designed to replace cracked, broken or faded handles so doors open and close normally. What it does

• Replaces damaged or discolored exterior door handle to restore function and appearance
• Provides a secure grip for opening and closing the appliance door
• Fits the factory mounting points for a clean, factory-like finish
• Helps eliminate rattling or loose-handle symptoms caused by worn or broken handles

• One white replacement handle

• Remove any trim or covers and fasteners holding the old handle; retain or replace screws as needed
• Align handle with factory mounting holes and secure with the original or supplied fasteners
• No electrical disconnection is typically required, but unplug the appliance or shut off power for access if working near controls
• Use proper hand protection to avoid sharp edges during removal and installation