Ge Pdt825ssj2ss Parts

The Bottle Hose Cover is an OEM replacement part for GE dishwashers. It refers to the protective plastic sheath that sleeves the circulation hose carrying water between the appliance and sink. Subject to prolonged exposure to heat and chemicals, the hose cover material can degrade.

Causes of a bad bottle hose cover include:

• Brittle or cracking vinyl from chemical deterioration over time
• Loose fit or sliding off the hose allowing kinks or sharp bends to form
• Holes or gaps exposing the underlying tubing to potential punctures

Symptoms of a failed hose cover include:

• Water leaks at connections if tubing is unprotected 
• Restricted water flow due to crimped tubing from improper routing
• Unsightly tubing detracting from the overall aesthetic

This GE replacement part is also compatible with some Hotpoint and RCA models.

The Friction Washer is an OEM component specifically designed for GE dishwashers. This friction washer is a thin circular part that creates resistance through surfaces rubbing together. It is often used beneath a mounting nut to prevent components from loosening during operation.  

Symptoms of a bad friction washer include loose or separating connections where the washer is installed, such as:

• Drain pump mounting fittings that become detached    
• Water connections that leak at the threaded joints
• Door handle mounts that allow play in the mechanism

Causes of failure can be cracks, wear or deformities in the washer that reduce its friction capabilities over time. Vibrations from use may also cause premature wear.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This left-hand attachment strip secures trim and panels for a clean, finished fit on compatible GE appliances. It helps maintain proper alignment and prevents gaps that can collect dirt or allow panels to shift during use. What it does:

• Attaches and stabilizes a side trim or panel to the appliance cabinet
• Keeps door/side trim aligned to reduce rattling or shifting
• Helps maintain an even, finished appearance along the appliance edge
• Addresses symptoms like loose trim, visible gaps, or panel movement

• One left-hand attachment strip

• Remove power to the appliance (or disconnect power source) before starting work
• Use basic hand tools; avoid forcing parts to prevent breakage
• Replace with OEM-specified hardware if fasteners are missing or damaged

This dishwasher hose clamp secures internal hoses to pumps or fittings, helping prevent leaks and disconnections. Replace a weakened or damaged clamp to restore a tight, reliable seal at the connection.

• Provides clamping pressure to hold a hose on pump, sump, or drain fittings
• Helps stop water leaking at hose joints
• Resolves: loose or disconnected hoses, water under the unit/base, or poor draining from a slipped drain hose
• Replaces worn, rusted, or deformed clamps after service

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward as needed for access; place a towel or pan to catch residual water
• Seat the hose fully, then compress or tighten the clamp per its design; position just behind the hose barb bead
• Run a short cycle and inspect for leaks at the connection

This right-hand door hinge arm assembly supports and guides the dishwasher door as it opens and closes. Replacing a bent or worn hinge restores smooth, balanced door motion and helps prevent abrupt, uncontrolled door movement.

• Serves as the right-side pivot for the dishwasher door
• Interfaces with the door spring/link mechanism to counterbalance door weight
• Helps maintain proper door alignment and smooth opening/closing
• Common signs of wear: door drops quickly, feels heavy, binds/creaks, or sits unevenly

• Disconnect power at the breaker before servicing; wear cut-resistant gloves
• Support the door to prevent sudden drop when removing the hinge arm
• The spring/link is under tension—release and reattach carefully
• After installation, check door balance and alignment; adjust spring/link tension if applicable

The Door Arm Hinge Assembly is an OEM component specifically designed for GE dishwashers. It is the mechanism responsible for securing the dishwasher door in place and facilitating smooth opening and closing motions. Reliable door hinges are essential for proper door alignment and a securely closed operation environment during cycles. 

Symptoms of a bad door arm hinge include:

• Squeaks or grinding noises heard from the door area
• Difficulty opening or closing the door  
• Door that does not stay securely shut
• Potential door or door frame damage from loose hinges

Replacement ensures your door operates safely and precisely as intended. Replace yours today with this genuine OEM GE part for trouble-free use.

Note: Left side

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

The Sump Manifold is an OEM component specifically designed for GE dishwashers. It is located within the sump pan and functions as an integral part of the dishwasher's drainage and circulation system. The sump manifold directs water flow during draining and refilling, ensuring proper water distribution to different areas of the dishwasher for cleaning and rinsing cycles. 

Symptoms of a bad sump manifold include:

• Issues with draining and water drainage
• Leaks within the sump pan area 
• Reduced or uneven water pressure during wash cycles
• Improper filling or distribution of water

Over time, components inside the sump manifold can break down or become clogged due to mineral buildup or leftover food particles. Regular maintenance is recommended to keep the sump manifold functioning optimally. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This Sideblaster inlet restores proper water delivery to the dishwasher's side jets, helping ensure targeted spray along the tub wall. A secure, leak-resistant connection supports consistent cleaning performance on items near the side spray area.

• Feeds water from the circulation system to the side-blaster jets on the tub wall
• Maintains a sealed pass-through to help prevent leaks at the side jet connection
• Helps correct weak/no spray from side jets and poor cleaning near the side of the tub
• Replaces cracked, loose, or damaged inlet fittings that can drip or reduce spray

• Disconnect power and shut off water supply before servicing
• Remove lower rack and panels as needed; you may need to pull the dishwasher out to reach the hose connection
• Transfer and reuse existing clamp/hardware; seat the seal properly and orient the inlet correctly
• Restore water/power and test for leaks and proper side-jet spray before reassembly

The Pan Leak is an OEM part for GE dishwashers. It is a machined pan located at the bottom of the tub that collects any residual water after a wash cycle finishes. 

Symptoms of a faulty leak pan include: 

• Puddles or residual water remaining in the bottom of the tub after a cycle
• Water not properly draining from the bottom tub area
• Potential for water damage issues if left unaddressed

Causes can be cracks in the molded pan housing, mineral deposits clogging the drainage channels, or warping preventing a proper seal.

Replacing with this authentic GE OEM part restores the tub's intended draining and drying functionality. It is compatible with Hotpoint, RCA, and Kenmore models as well to help prevent future water problems underneath the dishwasher.

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This blaster silverware assembly is the dishwasher spray component that directs wash water to the silverware area for better cleaning and rinsing. Replaces a cracked, clogged, or missing blaster to restore targeted spray action. What it does

• Directs high-pressure wash water to the silverware basket for improved cleaning of forks, knives, and spoons
• Replaces a broken, clogged, or leaking blaster that can cause poor silverware cleaning
• Restores proper spray coverage when the original assembly is worn or damaged
• Works with the dishwasher's lower spray system to help remove stuck-on food from utensils

• One blaster silverware assembly

• Disconnect power to the appliance before beginning any work
• Remove the lower rack to access the old assembly; installation typically snaps or screws into the lower spray/silverware area
• Inspect and clear nearby spray arm openings and filter screen of debris while replaced

This flexible silverware bellow seals and guides water flow around the dishwasher silverware basket, helping maintain proper spray circulation and keeping utensils contained for more consistent cleaning results. What it does:

• Replaces a torn or worn bellow that can allow utensils to block spray or shift during a cycle
• Helps direct wash water into the silverware area for more even cleaning
• Prevents small items from falling through gaps beneath the basket
• Reduces the chance of debris collecting where the basket meets the tub

• Disconnect power to the appliance before attempting any service.
• Typically snaps or slides into place; remove the silverware basket for access.
• Inspect surrounding gaskets and the basket for damage; replace if worn.

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

This right-side door trim is a factory-style replacement that restores the finished edge and appearance of the appliance door. It covers the door edge and trim mounting area for a clean, factory look. What it does

• Replaces cracked, chipped or worn right-side door trim to restore appearance
• Covers and protects the door edge and trim fasteners from dirt and damage
• Helps maintain the door's finished look after impacts or wear
• Fits into existing trim mounting points for a direct replacement

• High-level replacement only; follow for disassembly steps
• Remove any contents from the door and move shelves as needed for clearance
• Use proper tools to remove fasteners or trim clips; avoid forcing the trim to prevent damage

This top attachment strip secures the appliance's top panel and provides the mounting point for the door strike, restoring a stable, properly aligned front. It prevents panel movement and reduces rattles for a snug fit and reliable door engagement. What it does:

• Secures the top/front panel to the cabinet to maintain alignment and fit
• Serves as the mounting point for the door strike or latch components
• Helps eliminate rattling, vibration, and gaps at the top of the door area
• Restores reliable door engagement and prevents the strike from shifting

• Disconnect power to the appliance before beginning any repair
• Remove the top panel or access screws to reach the attachment strip; a screwdriver set is typically required
• Handle mounting tabs and edges carefully to avoid bending or damage
• Verify alignment of the door strike and test door closure after installation