Ge Zbd 6400 Parts

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This inlet transition is a molded connector that fits between the appliance cabinet and the inlet opening to guide incoming air and help maintain a sealed airflow path. It restores proper fit and reduces air leakage where the inlet meets the cabinet. What it does:

• Provides a finished, secure connection at the appliance inlet to direct airflow into the unit
• Helps reduce air leaks that can reduce drying/heating performance or cause airflow imbalance
• Replaces worn, cracked or broken inlet trim that can rattle or vibrate during operation
• Restores correct clearance and sealing where the inlet joins the cabinet

• One inlet transition piece

• Basic hand tools typically required; access the inlet area by removing the back panel or service panel as applicable
• Handle carefully to avoid bending or damaging adjacent trim and mounting tabs
• Disconnect power (and gas if applicable) before beginning service; follow all safety precautions in the appliance manual
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners for secure fit

This kick plate assembly replaces the lower access panel on compatible refrigerators and dishwashers to restore a finished look and protect internal components at the appliance base. It provides a clean, secure cover for the toe-kick area. What it does:

• Covers and protects the lower cabinet opening and components from dirt, debris, and accidental contact
• Restores the appliance's finished appearance at the base for a seamless look
• Helps direct airflow from vents located at the toe-kick area
• Replaces damaged, dented, or missing lower access trim to improve safety and aesthetics

• One kick plate assembly

• Remove power to the appliance before attempting removal or installation
• Typically fastens with clips or a few screws; retain hardware if reusing or replace if damaged
• Handle carefully to avoid scratching painted or plated surfaces during installation

Package of 12

Specs: 8-18 b por 1/2 ss

Specs: 10-16 b rnp 18/25

Size: 8-18 x 7/8 inch.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This sump clamping nut secures the washer/dishwasher sump seal and housing, helping keep the sump assembly sealed and stable during operation. It's a small but essential fastener for preventing leaks and maintaining proper drainage. What it does:

• Holds the sump/tub seal and sump housing tightly in place to maintain a watertight connection
• Prevents the sump assembly from loosening during spin or wash cycles
• Helps reduce leaks and related water damage when installed correctly
• Works with the factory sump and seal components as the retaining nut

• Replace only with the matching part number; verify orientation before tightening
• Hand-start threads to avoid cross-threading, then tighten to factory spec (do not overtighten)
• Disconnect power and water to the appliance before servicing

This pump motor hanger is the support bracket that secures the washer pump motor to the appliance frame, helping keep the motor stable during operation for reliable drainage performance. What it does:

• Holds the pump motor in the correct position to prevent vibration and misalignment
• Maintains pump-to-housing alignment so the drain pump can move water effectively
• Helps reduce unusual noise or movement caused by a loose motor mount
• Fits where the motor attaches to the washer chassis; replaces worn or bent hangers

• Disconnect power before starting any repair and follow basic electrical safety
• Basic hand tools required; keep original fasteners unless damaged
• Inspect pump and motor for wear while replacing the hanger

This replacement door strike secures the appliance door latch so the door stays closed and the gasket seals properly. It restores proper door engagement to help maintain temperature and prevent air leaks. What it does

• Provides a secure catch point for the door latch so the door closes and stays latched.
• Helps ensure the door seal engages fully to reduce cold air loss.
• Commonly replaced when the door won't stay closed, the latch slips past the striker, or the strike is cracked or worn.
• Fits into the door frame and aligns with the latch to allow smooth opening and closing.

• One door strike.

• Disconnect power before servicing and remove any stored items from the door area.
• Typical replacement requires removing trim or screws from the door frame; use proper screwdrivers and keep fasteners organized.
• Align the strike with the latch, secure fasteners snugly, and verify smooth latching and proper door seal after installation.