Gfe28gynefs Parts

Protective plastic cover that shields the appliance main control board from dust, moisture and accidental contact. Keeps the control electronics enclosed for safer operation and easier servicing without touching the board. What it does:

• Protects the main control board from spills, dust and physical contact that can cause shorts or damage
• Helps prevent accidental contact with live terminals during use or maintenance
• Keeps wiring and connectors secured and routed away from moving parts
• Restores the original enclosure for a proper OEM fit and finish
• Useful when the existing cover is cracked, warped or missing

• Always disconnect power to the appliance before servicing electrical components
• Remove interior panels or shelves as needed for access; retain mounting screws for reinstallation
• Align cover tabs and screw holes carefully to avoid stressing the board or connectors
• If the control board shows signs of damage, inspect or replace the board before reassembly

This deli pan top rear cover replaces the rear trim piece on the deli/warming top, restoring a finished appearance and protecting internal components from food, grease and spills. Keeps the deli area sealed and easier to clean. What it does

• Covers and protects the rear edge of the deli/warming pan top assembly.
• Shields wiring and internal components from food debris and grease buildup.
• Restores a proper fit and finish when the original rear trim is cracked, broken or missing.
• Helps maintain a clean, hygienic deli surface and simplifies wiping and maintenance.

• One deli pan top rear cover.

• Disconnect power to the appliance before beginning any service.
• Removal may require releasing clips or removing a few screws; keep hardware for reassembly.
• Handle the cover gently to avoid cracking; align tabs/clips before seating.

This foam seal is a flexible adhesive gasket that fills small gaps and cushions parts to help reduce air leaks and vibration in refrigeration assemblies. It restores a tighter fit where panels, liners or components meet. What it does:

• Seals gaps to help reduce air infiltration and potential frost buildup
• Cushions and isolates parts to reduce rattle or vibration noise
• Helps maintain proper airflow paths inside the appliance
• Useful for restoring a flush fit where foam or tape has deteriorated

• Unplug the appliance before starting any repair
• Clean and dry the surface; remove old sealant or adhesive for best adhesion
• Measure and trim the foam to fit; press firmly to ensure full contact
• Avoid stretching the foam; allow adhesive to set before closing panels or returning to service

This housing tray valve tank is the replacement housing that supports and secures the tray valve assembly, helping control water flow in the appliance. It restores proper valve positioning and prevents leaks from a damaged housing. What it does:

• Holds and aligns the tray valve assembly so the valve operates correctly.
• Provides a sealed mount to help prevent water leaks around the valve area.
• Replaces cracked, warped or otherwise damaged housings that cause misalignment or water seepage.
• Helps restore normal water delivery functions when the housing is the source of valve problems.

• One housing tray valve tank (housing) as shown

• Disconnect power and shut off the water supply before starting any work.
• Basic hand tools are normally required; handle plastic parts carefully to avoid cracking.
• Verify correct orientation and secure all fasteners and seals; test for leaks after re-connecting water.

This is a 60-gram can of R600a (isobutane) refrigerant for use in qualifying household refrigerators. It supplies the factory refrigerant type in a small service-sized can to restore proper cooling when the system has a low charge. What it does:

• Provides the correct R600a refrigerant used in many modern household refrigerators
• Helps restore cooling when low refrigerant is the cause of weak cooling or long run times
• Used during service to top off a sealed refrigeration system after leak repair or evacuation
• Not a repair for compressor or sealed-system mechanical failures

• R600a is a flammable refrigerant—use only in well-ventilated areas and keep away from open flames or sparks
• Inspect and repair any leaks before adding refrigerant; do not attempt to mix refrigerant types
• Follow proper disposal and recycling rules for refrigerant cylinders

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

This center track screw cover caps the exposed screw on the center track assembly to protect the screw head and give the track a finished appearance. It helps reduce debris buildup and prevents accidental snags on the screw head. What it does:

• Covers and protects the center track screw head from dirt, moisture, and surface wear
• Helps maintain a smooth surface on the track to reduce snagging or catching
• Restores the OEM appearance where the original cap is missing or damaged
• Small replacement part used with center track assemblies and trim pieces

• One center track screw cover (cap)

• Designed for simple push- or snap-fit installation over the exposed screw head
• Remove power to the appliance before accessing internal trim or track areas, and follow manufacturer safety guidance
• If screw or track is damaged, inspect and replace the underlying hardware before installing the cap
• Handle small parts carefully to avoid loss during installation