Gfe28jelfds Parts

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This water filter cover assembly secures the refrigerator's water filter cartridge and helps direct filtered water into the dispenser/ice system, restoring proper filter seating and reducing the risk of leaks or poor water flow. What it does:

• Secures and retains the water filter cartridge in its housing
• Seals the filter area to help prevent water leaks around the filter
• Directs filtered water from the cartridge into the dispenser and ice system
• Helps restore proper filter engagement when the original cover is cracked or broken

• Turn off water supply and remove power to the appliance before servicing
• Remove the old cover and verify filter type/orientation before installing the new cover
• Push the cover into place until the filter seats and locks per the appliance design
• Re-check alignment and seals; replace damaged gaskets as needed

This deli control PCB with overlay replaces the electronic control used to operate a refrigerator's deli drawer, restoring user input and display functions so the drawer can regulate temperature and respond to controls. What it does:

• Provides the control logic and interface for the deli drawer functions and display
• Responds to user inputs from the overlay buttons or touchpad
• Sends/receives signals to the main refrigerator control for temperature management
• Commonly replaces a board when deli controls are unresponsive, display is blank, or buttons fail

• Disconnect power to the appliance before beginning any service
• Handle the board by edges and avoid touching circuit contacts; observe ESD precautions
• Reassemble trim and panels carefully; test functions before finishing

This auger motor powers the ice-dispensing auger, turning and feeding ice from the freezer bin to the dispenser for smooth delivery. Replaces a worn or non-turning dispenser motor to restore ice dispensing function. What it does:

• Drives the auger shaft in the ice bin so ice is moved forward to the dispenser chute
• Stops rotation if motor fails, causing no ice to dispense
• Helps eliminate intermittent dispensing or reduced ice output when functioning properly

• Disconnect power to the appliance before beginning any work
• Remove the ice bin and access panels per your model's service instructions
• Inspect the auger, shaft, and bin for jams or broken fins before replacing the motor

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

A replacement fresh-food door handle that restores a secure grip and the finished look of the refrigerator door. Fits stainless finishes and replaces worn, cracked, or damaged handles to make daily use easier. What it does:

• Provides a sturdy grip for opening the fresh-food compartment door
• Replaces handles that are cracked, loose, or cosmetically damaged
• Restores proper alignment and ease of door operation when the original handle is broken
• Matches stainless finishes for a factory look

• Designed for direct replacement; use the factory mounting screws and brackets already on the door when present
• Turn off water/ice supply and empty door bins if they obstruct access before starting
• Handle small hardware carefully; keep screws and trim pieces together to avoid loss

The Freezer Handle is an OEM part for GE refrigerators. It allows for easy opening and closing of the freezer door. This freezer handle is designed to provide a sturdy grip, making it convenient to access your frozen food items.

A bad freezer handle can be caused by wear and tear over time, excessive force applied to the handle, or damage due to accidental impact or mishandling.

Symptoms of a bad freezer handle include:

• Difficulty in opening or closing the freezer door.
• Loose or wobbly handle.
• Cracks or breaks in the handle.

Replace your worn-out or damaged freezer handle with this OEM part and restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This port collar is a small trim/support piece used on select refrigerators. It reinforces the port opening and helps secure the mating tube or component for proper alignment, a snug fit, and a clean, finished appearance.

• Supports and spaces the port/opening where a tube or component passes through the cabinet or liner
• Helps maintain alignment and a secure fit to minimize gaps or vibration
• Replace if the collar is cracked, warped, or missing
• Symptoms can include a loose connection at the opening, rattling, or a visible gap or misalignment

• Unplug the refrigerator; shut off the water supply if working near water lines
• Use your model's parts diagram to access the port; remove any trim, clips, or screws
• Note orientation; press or snap the new collar into place and transfer any seals if present
• Reassemble and restore power; verify proper fit and operation

Manufactured by GE, this is a compressor kit for a refrigerator. The compressor's job is to pressurize the system and warm the refrigerant while propelling it through the rest of the cooling system. The compressor is controlled by a thermostat inside the refrigerator. When the thermostat detects a high temperature, the compressor engages, helping to cool the refrigerator and preserve food.Compressors are the core of the refrigeration system. There are also subject to a great deal of wear and tear through normal cycling on and off. In addition, compressors can be damaged if they run out of oil, if contaminants enter the system, and through exposure to prolonged operation due to a faulty thermostat or low refrigerant levels. When the compressor fails, the refrigerator will no longer be able to maintain a safe temperature for food. This is a complete replacement kit.This kit is a genuine OEM part and is sold individually. It is only compatible with GE refrigerators.

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

This is a replacement round-head 10-32 x .353 screw used to fasten appliance panels and internal components. It restores secure mounting and helps stop rattling or loose parts caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or small assemblies where a 10-32 machine screw is specified
• Stops movement and vibration that can cause noise or misalignment
• Replaces missing, stripped, or corroded fasteners to restore proper fit
• Matches the original fastener size and head style for correct clearance

• One 10-32 x .353 round-head screw

• Use the matching driver (typically a Phillips or slotted driver as required by the head) and avoid over-torque to prevent stripping
• Disconnect power and follow safety procedures when accessing internal components
• If other fasteners appear damaged or corroded, inspect and replace as needed

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

The Cover Front Panel Assembly is an OEM component for GE side-by-side refrigerators. Forming the handle and facade area of the fresh food compartment door protects inner mechanics while maintaining aesthetic integrity. Dependable operation relies on an intact front panel assembly.

Symptoms of a defective assembly include:

• Misaligned or loose-fitting facade panels detracting from appearance   
• Drafts noticeable around door perimeter compromising energy efficiency
• Poor fit inhibiting smooth door closure or opening  

Causes involve years of use compromising anchor clips through opening/closing stress, moisture exposure distorting composite materials, or impacts dulling factory sheen over time.

Replacing with this genuine GE assembly restores a factory finish look while supporting full door function. Compatible with Hotpoint, RCA, or Kenmore models seeking to preserve operation with an aesthetically pleasing front.
 

This right-hand freezer holder slide secures a freezer shelf or drawer in place so it operates smoothly and stays aligned. It replaces a worn or broken slide to restore proper shelf support and prevent slipping or binding. What it does

• Guides and supports the freezer shelf/drawer on the right side for smooth in-and-out movement
• Replaces cracked, broken, or worn plastic slide hardware
• Helps stop shelves or drawers from sagging, catching, or sliding out unexpectedly
• Works with the freezer compartment's shelving system to maintain proper alignment

• Disconnect power to the appliance before beginning any repair
• Typically replaces the existing right-side slide; remove the shelf/drawer to access mounting points
• Handle plastic parts gently to avoid cracking; inspect adjacent clips or supports for wear