Gfwn1oooliww Parts

This drain hose coupling joins two sections of a washer's drain hose to create a secure, leak-resistant connection. Replace a cracked or loose connector to help prevent leaks and support proper draining performance. What it does

• Connects two drain hose sections for proper water discharge
• Maintains a tight, sealed joint to help prevent leaks at the hose connection
• Restores a secure hose path if the original coupling is cracked, worn, or missing
• Common symptoms: water on the floor during drain, loose hose connection, or hoses separating

• Drain hose coupling

• Disconnect power and turn off water before servicing; pull the washer forward for access
• Place a towel or pan to catch residual water from hoses
• Loosen hose clamps, remove the old coupling, fully seat both hose ends on the new coupling, and tighten clamps securely
• Run a brief drain/rinse and inspect the connection for leaks

The Pressure Switch is an OEM part for GE washers. This part monitors and controls the water level inside your GE washer during the different cycles.

The water level pressure switch ensures accurate water level detection and regulation. It senses the pressure changes in the washer's tub as it fills with water, signaling the control board to stop the water flow once the appropriate level is reached.

A bad water level pressure switch can occur due to mechanical failure, electrical issues, or clogs in the pressure hose. If you notice symptoms such as the washer overfilling or underfilling with water, the water level not adjusting correctly, or error codes indicating a faulty pressure switch, it may be time to replace the component.

Symptoms of a bad water level pressure switch include:

• Washer overfilling or underfilling with water
• Water level not adjusting correctly
• Error codes indicating a faulty pressure switch

Ensure water level control by replacing the faulty water level pressure switch with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

EMI filter reduces electrical noise on the appliance's incoming power line to help protect electronic controls and cut down on radio/TV interference. It restores proper power filtering for appliances that show noise-related control issues. What it does:

• Filters electromagnetic and radio-frequency interference on the power input to prevent electrical noise from affecting control boards and sensors.
• Helps reduce visible or audible interference with nearby electronics such as radios, TVs, and audio equipment.
• Can address intermittent control errors, unexpected resets, or erratic operation linked to line noise.
• Provides the correct connection point for the appliance's power input so the control circuitry receives cleaner power.

• Disconnect power at the breaker and unplug the appliance before starting any work. Verify power is off with a tester.
• Match wiring colors and terminal types; secure all connections and route wires clear of moving parts.
• Some installations require removing access or control panels—retain fasteners.

This ST4 x 20 screw replaces a lost or damaged fastener and secures panels or brackets in your washer, restoring a tight fit and helping eliminate vibration and rattling caused by loose hardware.

• Fastens panels, brackets, or covers to the washer cabinet
• Replaces missing, stripped, or corroded screw specified as ST4 x 20
• Helps keep components aligned to reduce vibration and noise
• Useful during reassembly when the original screw won't hold

• Disconnect power before servicing; turn off the water supply.
• Match the screw length and thread to the original location; do not mix different screws.
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening.
• Transfer any original spacers or washers used with this screw.

A replacement M12 x 25 flange bolt used to secure appliance components where a washer-style bolt head is required. Durable fastener that restores proper fit and helps stop movement or vibration in assemblies. What it does:

• Secures panels, brackets or assemblies that use an M12 flange-style fastener.
• Restores proper clamping force when an original bolt is stripped, corroded, or missing.
• Helps eliminate rattling, loose parts, or misalignment caused by a failed fastener.
• Works wherever a metric M12 x 25mm flange bolt is specified by the manufacturer.

• One flange bolt (M12 x 25)

• Disconnect power and follow manufacturer safety instructions before servicing.
• Use the correct socket or wrench to avoid rounding the head; tighten to the appliance manufacturer's torque specification.
• Inspect mating threads and replace if damaged; do not force a damaged bolt.
• If the OEM manual calls for threadlocker or a specific torque, follow those instructions.

This softener bleach cover is the replacement dispenser cap that seals the laundry softener/bleach opening and helps prevent spills and contamination. It restores a clean, controlled dispensing area for softener and bleach. What it does:

• Covers and seals the softener/bleach dispenser to prevent leaks and accidental spills
• Helps keep the dispenser area clean and reduces residue buildup
• Restores proper fit and alignment of the dispenser opening
• Commonly replaced when cracked, warped, missing, or failing to seat properly

• One softener bleach cover

• Disconnect power to the appliance before servicing if access requires reaching inside the cabinet
• Remove any remaining product from the dispenser and clean area before installing
• Typically snaps or fits into place—avoid forcing or prying to prevent damage

Small self-tapping screw used to secure appliance panels and internal components. Replaces worn or missing fasteners to restore proper fit and alignment for covers, brackets, and trim pieces. What it does

• Secures sheet-metal panels, brackets or trim to the appliance chassis
• Replaces stripped, corroded or missing screws that allow rattling or loose parts
• Helps restore proper panel alignment and prevents vibration noise
• Works where a self-tapping thread is required in thin metal or plastic mating parts

• Power off and unplug the appliance before servicing
• Use the correct screwdriver bit to avoid cam-out and head damage
• Start threads straight and drive carefully—do not overtighten to avoid stripping
• Replace like-for-like; match screw length and thread type to the original

This is a replacement self-tapping screw used to secure panels, brackets and small components on compatible appliances. It provides a direct-fit fastener for repairs where the original ST4 x 25 mm screw is missing or damaged. What it does

• Fastens trim, access panels, brackets and internal components that use an ST4 x 25 mm self-tapping fastener
• Restores proper fit and reduces rattles or loose parts caused by stripped or missing screws
• Matches the OEM thread and length for a secure hold in sheet metal and plastic mounting points
• Useful for routine appliance repairs and refurbishments

• Use the correct size screwdriver or bit to avoid stripping the head
• Start threads slowly and avoid over-torquing to prevent stripping or cracking mounting material
• Ensure the appliance is unplugged or power is disconnected before servicing
• Keep removed hardware organized to verify correct replacement locations

This is a ST4.2 x 9.5 mm self-tapping screw used to secure panels and components in appliances. It replaces missing or stripped fasteners to restore proper fit and function of covers, brackets, and trim. What it does:

• Secures control panels, trim pieces, brackets or small components
• Replaces missing or damaged fasteners that cause loose or rattling parts
• Provides a durable threaded hold in sheet metal or plastic mounting points
• Helps restore proper alignment and prevent vibration-related noise

• One ST4.2 x 9.5 mm self-tapping screw

• Unplug the appliance power before beginning any repair
• Use the correct screwdriver bit to avoid stripping the screw head
• Apply firm, steady pressure and do not overtighten to prevent thread or material damage
• If original mounting hole is damaged, inspect and repair the hole before installing