Ghdp490efww Parts

This is a genuine GE replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. A simple fastener that helps keep assemblies aligned and functioning safely. What it does:

• Secures panels, brackets, and small components in place
• Prevents noise from loose parts and maintains structural alignment
• Restores proper fastening after repairs or wear
• Matches OEM fit for reliable replacement

• Disconnect power to the appliance before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully and tighten until snug; do not overtighten to prevent damage
• Replace any damaged or missing fasteners with the same OEM part for best results

This motor support is the stamped metal bracket that secures the dryer motor and blower assembly, keeping components aligned for smooth operation. It restores proper motor mounting and reduces noise from loose or misaligned parts. What it does:

• Holds the dryer motor and blower housing in the correct position to prevent wobble or misalignment
• Helps maintain proper blower alignment for effective air movement
• Supports safe, reliable motor operation when the original bracket is bent, cracked, or worn

• Disconnect power (unplug electric or shut off gas and breaker) before beginning repair
• Access requires opening the dryer cabinet and removing the drum and/or front panel on many models
• Inspect related components (motor mounts, blower wheel, idler, belt) and replace if damaged

This backsplash graphic assembly restores the printed control console area on electric ranges and cooktops, improving appearance and readable labels for controls. It replaces a cracked, faded, or peeling backsplash graphic to restore a clean, finished look. What it does:

• Replaces the printed graphic on the back console so button/knob labels and markings are visible
• Covers cosmetic damage like scratches, fading, peeling, or delamination of the original graphic
• Helps make controls easier to read and gives the range a refreshed appearance
• Fits into the range backguard/console area and acts as the visual overlay for controls

• One backsplash graphic assembly (single graphic/overlay piece)

• Disconnect power to the appliance before beginning any service
• Removal typically requires removing console/backguard screws and carefully lifting the old graphic away
• Handle the new graphic by the edges to avoid fingerprints or damage to the printed surface

This electronic support control board replaces a failed dryer control module to restore proper cycle selection and electronic functions. It mounts behind the console and routes signals between user controls and the dryer's power components. What it does:

• Receives inputs from the user control and sends commands to the timer, heating element/valve, and motor circuits.
• Helps manage cycle selection, start/stop, and timed functions.
• Works as part of the dryer's control system—does not include service diagnostics or additional modules.

• One support pc board (single control board only)

• Unplug the appliance before starting; disconnect power at the breaker for hard-wired units.
• Handle the board by its edges and avoid touching components to reduce ESD damage.
• Transfer any mounting brackets, harnesses, or shields from the old board if not pre-attached.

A replacement silicon controlled rectifier (SCR) that restores electronic power switching in the appliance's control circuitry. This SCR provides reliable on/off switching for motors or heating circuits when the original SCR has failed. What it does:

• Acts as an electronic switch to control power delivery to heating elements or motors
• Commonly fails when the appliance has no heat, intermittent operation, or won't run consistently
• Replaces a burned, shorted, or open SCR to restore normal control-board switching behavior
• Helps stop arcing or erratic performance when the original semiconductor has degraded

• For safety, disconnect power before accessing control electronics or replacing the SCR
• Handle the SCR and circuit board carefully to avoid ESD damage; use proper grounding if available
• Verify correct orientation and secure mounting; ensure all wiring and connectors are seated properly

This right-hand end cap replaces the factory cap that protects and finishes the outer edge of the appliance door or rail. It restores a secure fit and the original appearance where the end cap is cracked, damaged, or missing. What it does:

• Covers and protects the end of a door/rail to prevent sharp edges and wear
• Holds the rail/door trim in position to help maintain proper alignment
• Stops rattling or snagging caused by a broken or loose end cap
• Restores finished appearance to the appliance exterior

• Disconnect power to the appliance before beginning any repair.
• Installation typically requires basic hand tools; remove the old cap and snap or fasten the new cap into place.
• Handle parts carefully to avoid scratching the finish; verify right-hand orientation before installing.
• If mounting hardware is present on the original part, reuse only those pieces explicitly required for installation.

This housing PC board is the protective plastic housing that secures and supports the appliance control (PC) board, helping keep the control electronics stable and protected from damage or moisture during operation. What it does:

• Holds and secures the control (PC) board in the appliance chassis to prevent movement and shorting.
• Protects the control board from incidental contact, dust, and minor moisture exposure.
• Restores proper board alignment when cracked, warped, or broken housing causes loose connectors or intermittent electronics.
• Can help resolve symptoms such as intermittent control operation, loose connectors, or visible board exposure.

• One housing PC board (1 each) as shown.

• Disconnect power to the appliance before beginning any work to avoid shock or damage.
• Handle the PC board and housing carefully; avoid touching circuit traces or components.
• Installation typically requires removing panels and unplugging wire harnesses; keep track of fasteners and connector locations.

Includes 12 screws.