Ghws3605frr-Flwasher Parts

This drawer body dispenser is the molded housing that holds and supports the refrigerator dispenser assembly, restoring a secure, leak-free enclosure for water and ice delivery. Fits the dispenser opening and provides the mounting for internal components. What it does:

• Houses the dispenser components and provides structural support for the dispenser assembly
• Directs water/ice flow and helps maintain a sealed path to prevent leaks
• Replaces cracked, warped, or damaged dispenser housings that cause wobble or leakage
• Helps restore proper alignment of the dispenser chute and mounting points

• One drawer body dispenser housing

• Disconnect power and turn off the water supply before beginning
• Handle the housing carefully to avoid damaging mounting tabs or seals
• Transfer any gaskets, brackets, or internal components from the old housing
• Test the dispenser and check for leaks after reassembly and restoring power/water

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

A replacement siphon cap that seals the end of a siphon or drain tube to help prevent leaks and maintain proper drainage. Fits into the siphon assembly to keep water routed where it should for reliable operation. What it does

• Seals the siphon/drain tube connection to help prevent water leaks or drips
• Helps maintain proper siphon action and drainage performance
• Keeps contaminants out of the siphon opening
• Restores a secure connection when the original cap is cracked or missing

• One replacement siphon cap

• Disconnect power and shut off water to the appliance before starting
• Remove any tubing carefully; inspect mating surfaces for damage or debris
• Press the cap into the siphon tube/port until fully seated; confirm a snug fit
• After installation, restore power/water and check for leaks during a short test cycle

Size: 8 - 18 ab.

This stainless steel machine screw secures appliance components and trim for a reliable, corrosion-resistant hold. Use it when replacing lost or damaged fasteners to restore proper fit and reduce noise or misalignment. What it does:

• Fastens panels, brackets, and small assemblies where a #8-28 threaded screw is required
• Provides a rust-resistant connection for wet or humid appliance areas
• Helps stop rattling, loose trim, or misaligned parts caused by missing or stripped screws

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully by hand to avoid cross-threading; tighten until snug—do not overtighten
• Keep removed screws organized to ensure correct reassembly

This manual dispense body assembly replaces the dispenser body that directs water through a refrigerator's exterior dispenser. It restores proper dispensing control and helps stop leaks or poor flow at the dispenser outlet. What it does:

• Replaces the dispenser body that channels water to the door-mounted dispenser valve and spout
• Helps stop leaks or dripping at the dispenser area when the body is cracked or worn
• Restores stable lever/actuator engagement for reliable manual dispensing
• Addresses symptoms like slow or intermittent dispensing and water pooling at the door

• One manual dispense body assembly

• Disconnect power and shut off the water supply before beginning work
• Replacement typically requires removing the refrigerator door/dispenser trim to access mounting hardware
• Handle gently to avoid damaging the dispenser actuator or water fittings; inspect gaskets and seals and replace if damaged
• After installation, restore power and water, check for leaks, and operate the dispenser to confirm proper function

This replacement screw secures panels and components on compatible appliances, providing a reliable threaded fastener for repairs and reassembly. Use it when original fasteners are missing, stripped, or corroded to restore proper fit. What it does:

• Fastens appliance panels, trim, and brackets where a #10-14 thread with 5/8 in. length is required
• Replaces worn, stripped, or corroded screws to eliminate rattling and improve part alignment
• Flat Phillips head sits flush for a clean finish and correct panel seating
• Designed for appliance use — resists loosening under normal operation

• One screw as described

• Use the correct #2 Phillips driver and moderate torque to avoid stripping the head or threads
• Disconnect power and follow appliance safety procedures when accessing internal components
• If fastening into plastic or thin sheet metal, use steady pressure and avoid over-tightening

This small closed grommet seals and cushions a screw hole to protect wiring and reduce vibration. It prevents chafing where a fastener passes through a sheet-metal panel, helping maintain safe wiring and a quieter appliance. What it does:

• Seals a screw or bolt hole to keep wires and harnesses from rubbing on sharp edges
• Cushions and isolates vibration to reduce noise and wear
• Helps maintain a tight fit where panels or components meet
• Commonly used where a harness or lead passes through a chassis opening

• One closed grommet

• Inspect panel edges and harness before installing; replace if damaged
• Push grommet into the hole until fully seated; route wiring through the grommet
• Disconnect power to the appliance before any access or repairs

This silicon controlled rectifier (SCR) switches and regulates power in compatible appliance control circuits, helping the unit deliver correct power to heating elements or motors. It's a direct replacement component when the original SCR fails. What it does

• Acts as a solid-state switch that controls current flow to heating elements, motors or other high-current circuits.
• Fails open or shorted when worn; common symptom is loss of heating, intermittent power to the controlled component, or no operation on affected circuits.
• Provides fast, repeatable switching compared with electromechanical relays.
• Designed for stud-mount installation with insulated/marked terminals for correct wiring.

• One silicon controlled rectifier (SCR) as listed.

• Disconnect all power before accessing or replacing the SCR to avoid shock or equipment damage.
• Note terminal orientation and wiring before removal; replace with the same terminal/stud configuration.
• Avoid electrostatic discharge to the replacement part; handle by the body and avoid touching terminals.

This shipping bracket is a transport stabilizer that secures internal components during delivery and handling to prevent movement and damage. It removes after installation so the appliance can operate normally. What it does:

• Holds internal parts steady during shipment to protect fragile components
• Prevents movement-related damage while the appliance is transported
• If left installed, may cause vibration, noise, or prevent proper operation
• Used by technicians and installers when preparing or unpacking appliances

• Unplug the appliance and follow manufacturer's unpacking instructions before removing or installing
• Remove only the fasteners explicitly securing the bracket; keep hardware for reinstallation if needed
• Keep the bracket and hardware for future transport; do not leave bracket installed during normal operation

Size: 8-18 b.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Tub Front is an OEM part for GE washing machines. This component forms the front panel of the washing machine tub and helps securely hold the door in place. As one of the primary structural elements of the washing machine, the tub front is responsible for maintaining the integrity of the tub assembly and containing water during wash cycles.

Causes of a bad tub front can include wear and tear over time, cracks or breaks due to heavy impacts, or damage from attempts at non-OEM repair. 

Symptoms of a bad tub front include:

• Leaks or water seepage from around the door seal or tub area  
• The door no longer closes or latches securely
• Excessive movement or wobbling of the tub assembly
• Cracks, breaks, or bends in the plastic tub front panel

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts