Glb30tdsa Parts

This terminal nut secures a wire terminal to a threaded post or terminal block, ensuring a tight, reliable electrical connection. Replace a missing, stripped, or heat-damaged nut to restore a safe, stable power path to the component. What it does:

• Clamps a ring or spade terminal to a threaded stud/post on a terminal block or component
• Maintains a low-resistance connection to reduce arcing and heat buildup
• Helps address symptoms like loose/burned terminal connections, intermittent power, or discoloration at the connection point
• Direct replacement for the original connection hardware on applicable models

• 1 terminal nut

• Disconnect power at the breaker before servicing; allow any heated components to cool
• Note wire locations; remove damaged hardware and inspect wiring/terminals for heat damage
• Clean threads and install the new nut; tighten snugly without overtightening
• Reassemble and restore power; verify the connection remains cool during initial operation

Replacement screw used to secure panels, trim, and internal components in Frigidaire appliances. Restores proper fit after repairs and helps eliminate rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to maintain correct alignment and fit
• Prevents vibration and rattling caused by loose or missing fasteners
• Use when original screw is missing, stripped, or damaged
• Matches common fastener locations on affected Frigidaire appliances

• Disconnect power and water before starting any repair
• Use the correct driver to avoid stripping the screw head; hand-start to ensure alignment
• Do not overtighten; tighten until snug to avoid damaging threads or plastic parts

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

This jumper is an OEM-style electrical wire connector used to bridge terminals in a Whirlpool appliance to restore circuit continuity and proper component operation. It's a simple replacement part that helps return power or signal paths when the original jumper is damaged. What it does

• Provides a secure electrical connection between two terminals to complete a circuit.
• Restores power or signal routing to components that lose function due to a broken or corroded jumper.
• Common symptom: component or control doesn't receive power or the appliance won't complete a specific cycle.
• Works with control boards and wiring harness assemblies where a factory jumper is used.

• One jumper electrical connector.

• Disconnect power (unplug appliance or shut off breaker) before service to avoid shock or damage.
• Use insulated tools as needed and make secure, tight terminal connections to prevent arcing.

Size: 8-32 x 1/2 inch.

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

This replacement frame restores the appliance's outer trim and helps hold the control/door area together for a clean, finished appearance. It's a direct-fit exterior trim piece that replaces damaged or worn frames. What it does:

• Replaces a cracked, chipped, warped or bent trim/frame that affects appearance
• Secures and aligns the surrounding control or door components to reduce gaps and rattles
• Covers internal edges to help keep out dust, moisture and debris
• Restores the original look after impact or wear

• Disconnect power to the appliance before starting any repair
• Remove required trim, screws or clips to access and replace the frame; keep fasteners for reuse unless damaged
• Handle edges carefully—trim pieces can be sharp; use proper hand protection

This support mounting bracket secures and aligns internal components to keep assemblies stable and operating smoothly. It helps prevent part movement that can cause noise, misalignment, or improper panel fit. What it does:

• Stabilizes and supports adjacent components or panels to reduce vibration and rattling
• Keeps doors or internal assemblies aligned for correct operation
• Prevents shifting that can lead to intermittent contact or wear
• Helps maintain proper spacing where a fixed mount is required

• Disconnect power or unplug the appliance before beginning work
• Handle sharp edges carefully and use the proper screwdriver or nut driver
• Reuse existing fasteners only if they are in good condition; replace stripped or damaged hardware

This is the center lid that fits into the washing basket/tub assembly to cover the center opening and help contain laundry during the wash cycle. It restores a proper seal and keeps items from entering the agitator area. What it does:

• Covers the center opening of the washer basket to prevent clothes from getting caught in the agitator
• Helps maintain normal wash action and water containment around the tub center
• Can resolve symptoms like items snagging near the agitator, visible gap in the basket center, or loose/missing center cover
• Matches OEM fit and geometry for correct placement in the basket assembly

• One lid, basket center

• Disconnect power and water to the appliance before beginning any repair
• Removal/install typically requires accessing the washer basket; follow the OEM service manual for steps
• Use hand tools as needed and avoid forcing plastic tabs to prevent breakage