Gld4200l00bb Dishwasher Parts

A small replacement clamp used to secure hoses and small assemblies to prevent leaks or disconnection. Fits the original mounting point and restores a tight seal where the worn clamp no longer holds reliably. What it does:

• Secures a hose or tubing connection to keep water or air from leaking
• Restores proper tension where the original clamp has loosened or corroded
• Helps stop intermittent leaks and prevents hoses from slipping off fittings
• Works in confined appliance areas where a compact clamp is required

• Turn off power and water to the appliance before starting any repair
• Use appropriate hand tools; avoid over-tightening to prevent hose damage
• Dispose of the old clamp and any corroded hardware; inspect surrounding fittings for wear

Includes 12 screws.

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This is a replacement 8-18 x 9/16 machine screw used to secure internal and external appliance components. It restores proper fastening and helps stop rattling or loose panels caused by worn or missing fasteners. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration
• Replaces stripped, corroded, or missing screws that can cause rattling or misalignment
• Helps maintain electrical and mechanical connections by holding parts in proper position
• Appropriate where an 8-18 thread size and 9/16" length are required

• Replacement screw

• Disconnect power to the appliance before accessing internal components
• Use the correct driver to avoid stripping the screw head and ensure proper torque
• Do not overtighten; snug until secure to avoid damaging threads or parts

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This silicon controlled rectifier (SCR) switches and regulates power to heating or motor circuits, helping the appliance control temperature and run cycles reliably. It's a direct-fit electronic switching component used in a variety of control systems. What it does:

• Acts as an electronic switch to regulate AC power to heating elements or motors
• Helps control temperature output and maintain consistent cycle performance
• Can prevent unwanted continuous current flow when functioning properly
• Commonly replaced when ovens, ranges, or dryers fail to heat or cycle correctly

• One silicon controlled rectifier (SCR) as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the SCR by its body; avoid touching terminals and static-sensitive areas
• Verify proper orientation and secure mounting; follow OEM wiring and torque practices

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This tiered upper rack kit replaces a damaged or missing upper rack to restore secure placement and organized spacing for cups, small plates and dishwasher-safe items. It helps improve loading capacity and prevents small items from tipping during cycles. What it does:

• Provides a tiered shelf for cups, mugs and small dishware to keep items secure
• Restores proper rack alignment and rolling action for smooth in-and-out movement
• Reduces shifting or tipping of small items that can block spray arms or cause poor cleaning
• Replaces worn or broken rack components so dishes load and drain correctly

• Disconnect power to the dishwasher and turn off water supply before starting
• Slide out the old upper rack and remove any retained clips or stops before installing the new rack
• Check rollers, rails and clips for wear and replace if needed to ensure proper operation
• Handle edges carefully and reassemble all stops and fasteners; test rack travel before running a cycle

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections