Gle02152es1 Parts

This damper gasket seals the air damper assembly to help maintain proper airflow and temperature control inside the refrigerator. It restores a tight seal around the damper so the fridge can cycle correctly and reduce air leakage. What it does:

• Seals the damper housing to prevent cold air from bypassing or leaking into the wrong compartment
• Helps maintain consistent internal temperatures and reduce frosting in the damper area
• Can reduce overworking of the compressor caused by air loss through a damaged gasket
• Addresses symptoms like uneven cooling, excess frost near the damper, or visible air gaps around the damper opening

• One damper gasket

• Disconnect power to the appliance before beginning any repair
• Remove damper housing or access panel as required to reach the gasket; handle plastic parts carefully to avoid cracking
• Ensure mating surfaces are clean and dry, then seat the gasket fully into the damper flange for a proper seal
• If any additional parts (clips, screws, or the damper assembly) are damaged, replace them as well to ensure correct fit and function

This wiring harness assembly routes power and signals between an appliance's control and its components to restore reliable electrical connections and operation. It replaces a damaged or corroded harness to help eliminate intermittent power or control issues. What it does

• Carries power and control signals between the appliance control board and internal components.
• Restores reliable electrical connections when wires are frayed, broken, or connectors are loose.
• Helps resolve intermittent operation, components not receiving power, or controls that don't respond.
• Prevents shorts caused by exposed wiring or damaged insulation.

• One pre-assembled wiring harness with factory-style connectors.

• Disconnect power (unplug appliance or shut off breaker) before starting work.
• Compare the new harness to the old one to confirm connector types and lengths before installation.
• Route and secure the harness away from moving parts and heat sources; use existing wire-retaining clips.

This top hinge and pin assembly secures the refrigerator door to the cabinet and provides a smooth pivot for opening and closing. Replacing a worn hinge helps restore proper door alignment and sealing. What it does:

• Holds the top of the refrigerator door in place and provides the pivot point for door movement.
• Restores correct door alignment when hinge wear causes sagging or uneven gaps.
• Helps the door close fully to maintain an effective seal and consistent internal temperature.
• Reduces binding or sticking when the door no longer pivots smoothly.

• One top hinge and pin assembly.

• Unplug the appliance or turn off power to any connected components before starting.
• Support the door while removing/installing the hinge to prevent damage or dropping.
• Installation typically requires removing the door or partially unmounting it — keep screws and hardware organized.
• After installation, check door alignment and gasket seating; adjust as needed for an even gap.

This replacement UI display restores the control-panel readout so you can see settings, clock, and status messages. It helps bring a clear, readable display back to your appliance for everyday use. What it does:

• Replaces the appliance control-panel display to restore visible numbers, symbols, and status indicators
• Commonly used when the display is blank, dim, flickering, or showing missing/garbled characters
• Works with the control/interface assembly to show oven/range or appliance function feedback
• Lets you confirm timer, temperature, and cycle information at a glance

• Always disconnect power at the breaker or unplug the appliance before starting work
• Handle the display gently to avoid damaging the lens, connectors, or ribbon cables

This harness cover is a molded protective shroud that shields and organizes the appliance wiring harness, helping prevent abrasion and accidental contact for safer, more reliable appliance operation. What it does:

• Protects wiring harness from rubbing, pinching, and physical damage
• Keeps wires neatly routed to reduce strain and accidental disconnection
• Helps reduce risk of shorting or arcing from exposed wiring
• Resolve symptoms like intermittent electrical issues or visible wire wear when the original cover is broken or missing

• Disconnect power to the appliance before starting any work.
• Remove access panels as needed to reach the wiring harness; replace the cover so clips or tabs fully engage.
• Do not alter or cut the cover; inspect wiring for damage and repair any frayed wires before reinstalling.