Glh566eesb4frigidaireside Parts

Size: 10-16 x 5/8 inch.

This front foot assembly is the adjustable leveling leg located at the front of the appliance. It supports and stabilizes the cabinet so it sits square and level, helping prevent rocking, vibration, and poor door alignment.

• Provides front support and height adjustment to level the unit
• Helps reduce rocking, vibration, and rattling during operation
• Replaces a worn, broken, missing, or stripped front foot
• Helps ensure doors or drawers align and close properly when leveled

• Disconnect power and, if applicable, shut off water/gas before servicing
• Protect flooring; carefully tip or brace the appliance to access the front foot
• Unthread the old foot; thread in the new foot and adjust until level side-to-side and front-to-back
• Verify stability, then restore utilities and recheck for level

Inlet valve filter

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This fixed blade sits inside the refrigerator's ice bucket/crusher assembly. It provides a stationary cutting edge that works with the auger and rotating blades to break up cubes, helping your dispenser deliver consistent crushed ice.

• Stationary crusher blade that works with the auger and rotating blades to crush ice
• Helps prevent whole cubes from passing through on the "crushed" setting
• Worn, bent, or missing blades can cause poor crushing, jams, or uneven ice size
• May help address symptoms like dispenser jamming, irregular crushed ice, or increased grinding noises

• Unplug the refrigerator before servicing; remove and empty the ice bucket
• Note the order and orientation of blades, spacers, and fasteners; take reference photos
• Handle sharp metal edges; wear cut-resistant gloves
• Reassemble in the original sequence and tighten hardware snugly; ensure the auger turns freely before reinstalling

This small but critical actuator spring restores return tension in a refrigerator's actuator mechanism, helping the lever reset to neutral after use so controls feel responsive and operation stops cleanly. What it does:

• Provides the return force for an actuator or lever so it moves back to its neutral position
• Helps the mechanism engage/disengage a switch cleanly
• Common symptoms of a weak or broken spring: lever sticks, feels loose, or doesn't spring back
• Contribute to intermittent activation or failure to stop when released

• 1 actuator spring

• Disconnect power; if working near the dispenser/water system, shut off the water supply
• Access the actuator mechanism and note the spring's exact orientation (take a photo before removal)
• Use needle-nose pliers to transfer the spring; do not over-stretch or deform it
• Wear cut-resistant gloves and eye protection; test lever return action before reassembly

This spacer fits the refrigerator door hinge to set proper clearance and alignment so the door swings smoothly and seals correctly. Replace a worn or missing spacer to eliminate rubbing and uneven gaps at the door.

• Maintains the specified distance between hinge components for correct door height and alignment
• Helps the door open and close without rubbing or binding
• Supports consistent gasket contact for a reliable seal
• Common signs of wear: door sagging, scraping noises, uneven gaps, or the door not closing flush

• Unplug the refrigerator; remove items from the door and support the door before working on the hinge
• Note the order of any washers, cams, and spacers during disassembly for correct reassembly
• Reinstall hardware in the same sequence; do not overtighten fasteners to avoid deforming the spacer
• After reassembly, check door alignment and gasket seal; adjust as needed

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

Color: White

Specs: 1.40`` long

Almond. Size: 13 oz. can. Acrylic appliance paint.

Used from harness to top.

This spiral pin secures components in place within the appliance assembly, providing a tight, durable fit that resists loosening under normal operation. Replacing a worn or missing pin helps restore proper alignment and dependable drive of the linked parts.

• Holds mating parts together with a press-fit connection
• Can help resolve issues like loose or slipping drive components, rattling, or intermittent operation in the affected mechanism
• Maintains correct alignment to reduce wear on adjoining parts

• Disconnect power and shut off water before servicing
• Support the assembly to relieve tension before removing the old pin
• Use the correct size punch/driver to press the pin out and in straight
• Do not force; inspect mating parts for wear and replace if damaged

Color: Almond

Right hand side

This kickplate grille mounts across the bottom front of the refrigerator. It restores a finished look and helps protect the machine compartment while allowing proper airflow through the condenser area.

• Covers the lower front opening to hide and shield internal components
• Vents air to support proper condenser airflow
• Replaces a damaged, cracked, or missing kickplate
• Common symptoms: broken tabs, grille won't stay attached, visible damage, missing piece

• Disconnect power before servicing
• Open doors to clear the grille; remove the old piece by releasing clips or removing screws
• Align the new grille with the mounting points and snap or fasten into place
• Ensure the grille sits evenly and doesn't interfere with door swing or airflow