Glh566eesb4frigidaireside Parts

Restore stable storage and help contain leaks with this Spill Safe Shelf. Replacing a cracked or missing shelf brings back usable space and helps prevent spills from dripping onto lower shelves and drawers.

• Supports food and containers on the designated refrigerator level
• Spill Safe design helps contain minor leaks to the shelf area
• Replace if the shelf is cracked, warped, loose, or missing
• Common symptoms: drips reaching lower shelves, shelf no longer seating correctly, reduced storage capacity

• Remove all items from the shelf area before replacement
• Slide the old shelf out; align the rear of the new shelf with the slots/rails, then lower the front until fully seated
• Do not force into place; use the correct rail position for your model
• Handle with both hands to avoid dropping or damaging the shelf

This refrigerator kickplate grille mounts across the lower front of the cabinet to cover the machine compartment while allowing proper airflow. Replacing a broken or missing grille restores a clean finish and helps keep debris away from internal components.

• Covers the lower opening and helps shield the condenser area from bumps and debris
• Helps direct air through the base for proper ventilation
• Restores a clean, finished appearance across the bottom front
• Typical symptoms: cracked or scuffed grille, broken mounting tabs, loose or won't stay attached, missing

• Disconnect power and wear work gloves to avoid sharp edges
• Open doors; on many models, pull the grille straight out to release spring clips. If screws are used, remove them from the base rail
• Align tabs/clips and snap or fasten the grille into place
• The grille is secure and clear of door swing and air inlets

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

This spacer is a small positioning piece used in refrigerator assemblies to maintain proper clearance and alignment between parts. Replacing a worn or missing spacer helps restore smooth operation and prevents rubbing or binding. What it does:

• Maintains the designed gap between mating parts to prevent friction and wear
• Helps keep assemblies aligned for smooth, consistent movement
• Reduces looseness, rattling, or poor fit caused by a missing or deformed spacer
• Typical signs include visible damage or a missing spacer and misalignment or scraping noises in the area it installs

• 1 spacer

• Disconnect power; if working near water components, shut off the water supply
• Use your model's parts diagram to determine exact location and orientation
• Retain and reuse original fasteners or clips unless damaged
• Do not overtighten hardware; ensure smooth operation after installation

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

Right handed Hinge

This lint screen lid hinge connects the dryer's lint lid to its mounting point, allowing smooth, aligned opening and secure closing. Replacing a bent or broken hinge restores proper lid operation and helps keep lint contained in the trap.

• Provides the pivot point for the lint screen lid/cover
• Helps the lid sit flush and stay aligned when closed
• Symptoms of a failed hinge can include a loose or misaligned lid, difficulty opening/closing, or squeaking/binding at the hinge
• Replace when the hinge is bent, cracked, or missing

• Disconnect power before servicing; sharp cabinet edges—wear cut-resistant gloves
• Support the lint lid to avoid bending or scratching
• Remove the mounting screws, note the hinge orientation, and transfer the new hinge in the same position
• After reassembly, cycle the lid open/closed to ensure smooth operation before restoring power

Right side.

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

2 Port. Whirlpool and Kenmore washers.

Color: Black

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

Screw: 8-16 x 3/8 inch.

Replacement refrigerator interior light socket that secures the interior lamp and connects it to the cabinet wiring, restoring reliable interior illumination. Use this when the light fails to come on, flickers, or the bulb sits loosely. What it does:

• Holds the interior lamp and provides the electrical connection for lighting
• Restores consistent contact to prevent flicker or intermittent operation
• Common repair for a light that won't turn on or a bulb that won't stay seated
• Fits into the interior housing to maintain proper lamp alignment

• Disconnect power to the appliance before inspecting or replacing the socket
• Remove the bulb before swapping the socket to avoid breakage or shock
• Inspect wiring and connectors for damage; replace if wiring is frayed
• Avoid getting the socket wet and use only the correct bulb type and wattage specified by the appliance

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long