Gns23gshss Parts

This is the clear glass that sits atop the crisper/vegetable drawers, creating a sturdy shelf and sealing the bins to help maintain proper humidity. Replacing damaged glass restores a flat, clean surface for food storage.

• Forms the shelf surface over the crisper/vegetable drawers
• Helps seal the produce bins for better moisture control
• Replace if cracked, shattered, sagging, or missing
• Common symptoms: broken glass, unstable or uneven shelf, items tipping in the crisper area

• Unplug the refrigerator and wear cut-resistant gloves
• Remove food from the shelf, lift out the old glass carefully
• Clean the frame/ledges before setting the new glass in place
• Ensure the glass is fully seated and supported on all edges

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

This water tank assembly sits inside the refrigerator compartment and stores a reserve of water for the door dispenser. Replace it to stop leaks and restore proper, chilled water flow when the original reservoir cracks or bursts.

• Holds a supply of water for the door dispenser inside the fresh food section
• Uses refrigerator air to help deliver chilled water on demand
• Restores proper flow when a reservoir is cracked, leaking, or frozen/burst
• Typical symptoms: water under drawers, weak or no water from the dispenser, or warm water at the dispenser

• Disconnect power and shut off the household water supply before servicing.
• Remove shelves/drawers to access the tank; note tube routing and connection points.
• Release water lines per your connector type; ensure tube ends are cut square and fully seated during reassembly.
• Restore water, check for leaks, and run the dispenser to purge air from the system.

This refrigerator main control board assembly is the appliance's central electronic module. It regulates cooling, defrost, and fan functions and communicates with sensors and the user interface to help maintain proper temperatures and stable, reliable operation.

• Controls compressor and fan motors to reach set temperatures; failure can cause no-cool, warm spots, or intermittent cooling
• Manages the automatic defrost cycle; issues may lead to frost buildup or over-freezing
• Coordinates power to lights, dispenser, and control panel; faults may cause unresponsive displays, beeping, or erratic behavior
• Monitors thermistors and system loads; problems may result in rapid clicking, frequent restarting, or failure to start

• Disconnect power before servicing; use ESD protection to avoid static damage
• Access is typically from the rear of the cabinet behind a service cover
• Move wire connectors one at a time to matching keyed terminals; avoid touching component solder pads
• Ensure all harnesses are fully seated and the board is secured before restoring power

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This mullion articulation assembly mounts on the fresh food door and flips out to form the center seal between French doors, helping the refrigerator close properly while reducing air leaks and moisture at the door gap.

• Flips between doors to create the center mullion seal in the fresh food compartment
• Helps maintain proper door alignment and smooth closing
• Damage or wear may cause poor sealing, condensation or frost at the center, or temperature issues
• Common clues include a broken hinge/pivot, warped or loose rail, or a flipper that sticks

• Disconnect power before servicing
• Remove door bins/shelves for access, then take out the screws or clips securing the old mullion; note orientation
• Position the new assembly, transfer any caps/fasteners if needed, and tighten securely
• Close both doors to ensure the flipper moves freely and the center seal is even

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This refrigerator French door gasket restores a tight seal around the door opening. Replacing a worn or damaged gasket helps keep cold air in and humid air out to maintain stable temperatures and reduce condensation. What it does:

• Forms an airtight seal between the door and the cabinet on French-door models
• Helps prevent warm air leaks, moisture buildup, and frost around the door opening
• Replace if torn, warped, cracked, or if gaps remain when the door is closed
• Common signs include condensation on or around the gasket and the door not sealing fully

• 1 door gasket

• Unplug the refrigerator and remove items from the door bins
• Warm and relax the new gasket (soak in warm water or use low heat) to remove kinks; do not overheat
• Lift the old gasket out of the retainer; if your model uses retainer screws, loosen them, swap the gasket, then re-tighten
• Press the new gasket fully into the channel, ensure corners seat, then close the door and check for an even seal all around

The damper duct assembly regulates the cold air sent from the freezer into the refrigerator compartment. Replacing a worn or sticking damper restores proper airflow and helps the fresh food section maintain stable, even temperatures.

• Regulates airflow from the freezer into the refrigerator compartment
• Helps maintain set temperatures by opening and closing to meter cold air
• Common failure signs: fresh food too warm, items freezing near the vent, weak/no airflow from the vent, or clicking/buzzing from the damper area

• Disconnect power to the refrigerator before servicing
• Remove shelves and the duct/vent cover; retain screws and clips
• Unplug the wire harness and swap the assembly; transfer any reusable hardware
• Ensure seals seat fully to prevent air leaks; restore power and allow temperatures to stabilize

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn or warped gasket restores proper sealing to improve temperature control, reduce frost and condensation, and help your fridge run efficiently.

• Creates a continuous seal around the door perimeter to prevent air leaks
• Helps maintain consistent temperatures and humidity inside the compartment
• Reduces frost, ice, and condensation caused by warm air infiltration
• Common symptoms: tears or warping, visible gaps/light, door not closing fully or popping open, excess frost or moisture

• Unplug the refrigerator before servicing
• Lay the gasket flat and warm it with hot water or gentle heat to relax folds; do not overheat
• Remove the old gasket and press the new one fully into the retainer channel, starting at the corners
• Close the door and check for uniform contact all around; reseat or adjust hinges if needed

This manufacturer-specified screw fastens appliance panels, brackets, and internal components in place. Replace a missing or stripped fastener to restore a tight, rattle-free fit and reliable support at the original mounting points.

• Provides the correct fastener for securing covers, brackets, and assemblies
• Replaces lost, rusted, or damaged screws
• Helps resolve loose or vibrating panels and trim
• Maintains alignment of components and hardware

• Unplug the appliance; shut off water if working near supply lines
• Match the new screw to the original location; verify length and thread
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Keep removed hardware organized for reassembly

This hex-head screw secures refrigerator components where a 12-24 x 7/8 in fastener is specified. Replacing a missing, stripped, or rusted screw restores a tight, reliable fit for brackets, panels, and assemblies and helps eliminate vibration and rattles.

• Fastens panels, brackets, and other assemblies in the refrigerator at locations calling for this size hardware
• Replaces worn, stripped, or missing screws to restore secure mounting
• Helps correct loose or misaligned components and reduce vibration noise
• OEM size: 12-24 thread, 7/8 in length; hex head

• Disconnect power and, if applicable, shut off the water supply before service
• Match the screw to the original location; replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use an appropriate nut driver or socket that fits the hex head