Grss2352af Parts

Replacement trim that restores the appliance's finished appearance and protects exposed edges from damage. Installs at the exterior to cover gaps and give a clean, factory look. What it does:

• Conceals exposed edges and gaps for a neater, finished appearance.
• Helps protect door or cabinet edges from chips, scratches and normal wear.
• Replaces cracked, broken or missing trim that makes the appliance look worn.
• Typically snaps or screws into place.

• Disconnect power to the appliance before beginning any service.
• Support the door or panel as needed to avoid pinching or dropping during removal/installation.
• Remove and retain any original fasteners; trim may be snap-fit or screw-secured depending on model.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

The Motor Bushing is an OEM part for Frigidaire refrigerators. The bushing works to reduce vibration and surrounds the motor shaft, facilitating smooth rotational movement.

Causes can be normal wear over extensive use, lack of lubrication that increases friction, or damage from foreign object intrusion.

Symptoms of a bad motor bushing include:

• Excessive vibration causing noise during motor operation
• Reduced fan blade spinning speed or complete stoppage
• Motor shaft wobble or misalignment over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This shelf assembly is a tempered glass refrigerator shelf that restores usable storage space and a clean, stable surface for food storage. It replaces cracked, chipped or missing shelves to keep interior items supported and organized. What it does:

• Provides a sturdy, flat surface for storing food and containers
• Replaces damaged or missing glass shelves that cause items to tip or fall
• Helps maintain proper air circulation and organization inside the fresh-food compartment
• Fits into existing shelf supports or tracks to hold weight evenly

• One complete shelf assembly

• Remove all items from the shelf area before installation
• Lift into place on the existing shelf supports or slide into tracks until fully seated
• Handle tempered glass carefully; wear gloves and eye protection to avoid cuts
• No special tools or electrical disconnection required for shelf replacement

This genuine replacement screw secures appliance components and panels so parts stay properly aligned and rattle-free. Use it to replace a missing, stripped, or corroded fastener and restore a snug, reliable fit.

• Fastens brackets, covers, panels, and other hardware in their original locations
• Helps resolve loose or vibrating components and rattling noises
• Replaces missing or damaged hardware that can cause gaps or misalignment
• May be used in multiple locations

• Disconnect power; shut off water supply if working near water lines
• Compare to the original screw and install in the same location/orientation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Refer to your model's exploded view to verify quantity and placement

This bearing supports a rotating shaft to reduce friction and restore smooth, quiet operation. It replaces a worn bearing to help stop grinding, wobbling, or noisy rotation in the appliance. What it does

• Supports and centers a rotating shaft or drum to reduce friction and wear.
• Allows smoother rotation to reduce noise such as grinding, squealing, or rumbling.
• Helps prevent wobble or uneven rotation that can stress other components.
• When worn, can cause vibration, excess noise, or difficulty maintaining proper rotation speed.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle bearings and shafts carefully; keep parts clean and free of debris during installation.
• Use appropriate pullers/press or follow OEM instructions to remove/install; improper tools can damage the part.
• If other wear is present (seals, shafts, supports), inspect and replace as needed.

Left side.

This condenser coil assembly removes heat from the refrigerant so your refrigerator can maintain proper cooling. Replacing a damaged or clogged condenser restores heat rejection and helps the compressor run more efficiently. What it does

• Transfers heat from the refrigerant to the surrounding air so the system can cool interior compartments
• Helps prevent the compressor from running continuously by allowing proper heat dissipation
• Commonly fails when fins are bent, clogged with debris, or corroded, causing reduced cooling performance
• Can cause the refrigerator to run hot, overheat at the rear, or cycle abnormally when compromised

• One condenser coil assembly

• Disconnect power to the appliance before starting any repair
• Replacement typically requires removal of lower rear access panels and panel fasteners; keep hardware for reinstallation
• Handle the coil carefully to avoid bending fins or damaging tubing

This light assembly provides interior refrigerator illumination so you can see food and settings clearly. It restores a working interior lamp and replaces broken, cracked, or non-lighting housings for safer, more convenient use. What it does

• Houses the interior lamp and socket to deliver overhead illumination inside the fresh food compartment
• Restores lighting when the fixture is cracked, loose, scorched, or the lamp fails to come on
• Ensures proper mounting and alignment of the bulb for consistent light coverage
• Helps prevent accidental contact with the bulb and protects wiring inside the compartment

• One light assembly

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle lens and socket carefully; avoid forcing clips or screws to prevent breakage
• Replace the bulb with the manufacturer-recommended type and wattage; do not exceed specified limits

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim

NOTE - FOR AIR FILTER USE PART # PAULTRA QTY-1 OR PAULTRA2 QTY-2

This light assembly replaces the refrigerator interior lamp housing to restore interior illumination and safe bulb mounting. It provides a secure lens and socket assembly so the interior light functions correctly and stays protected. What it does:

• Houses and secures the interior lamp socket and lens for the refrigerator compartment
• Protects the bulb from contact with stored items and helps diffuse light for better visibility
• Restores proper lamp alignment and electrical connection when the old housing is cracked or broken
• Helps prevent loose bulbs and reduces risk of accidental bulb damage

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use appropriate screwdriver or trim tool to remove the old housing; handle the lens carefully to avoid scratching or breaking
• Wear gloves and eye protection when handling bulbs or broken parts

Color: Black. Rubber. Holds tube/wire

This condenser tube spacer positions and secures the refrigerator's condenser tubing to maintain proper tube spacing and airflow. Replacing a worn or broken spacer helps reduce vibration, rattling, and rubbing that can damage tubing over time. What it does:

• Holds condenser tubing in the correct position to preserve airflow and cooling efficiency
• Cushions tubing to limit vibration and reduce rattling noises
• Prevents tubing from rubbing against the cabinet or other components, lowering wear risk
• Helps reduce the chance of tubing fatigue that can lead to damage

• Disconnect power to the appliance before accessing rear panels or condenser components.
• Handle condenser tubing gently; avoid kinking, bending, or putting stress on lines during installation.
• Installation may require removing the back or lower access panel to reach the condenser assembly.