Gse25gghbcbb Ge Side Side Refrigerator Parts

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

This replacement screw secures refrigerator panels, brackets, and trim to help keep components aligned and quiet. It matches the specified #8-18 thread and 1-1/2 inch length used at designated mounting points.

• Fastens panels, brackets, covers, and hardware as designed by the manufacturer
• Restores a missing or damaged fastener to keep parts secure and aligned
• Correct #8-18 tapping thread and 1-1/2 in. length for specified locations

• Unplug the refrigerator or disconnect power before servicing
• Wear cut-resistant gloves to protect from sharp edges
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any model-specific washers or clips originally installed on your unit

This condenser assembly is the condenser coil used in compatible refrigerators to release heat from the refrigerant so the appliance can cool efficiently. Replacing a damaged coil helps restore proper cooling performance and energy use. What it does:

• Circulates refrigerant through the condenser coil to dissipate heat from the refrigeration system
• Supports normal compressor cycling and helps maintain steady internal temperatures
• Common symptom fixes: reduces long run times, improves inadequate or uneven cooling, and addresses overheating or noisy compressor operation
• Works with the condenser fan and other sealed-system components to complete the heat-exchange process

• Disconnect power to the refrigerator before servicing to avoid electric shock
• Access commonly from the rear lower panel or front grille; may require removal of kick plate or back cover
• Avoid damaging the coil fins; handle carefully and use fin comb if needed

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

This wire basket fits in the freezer compartment to restore usable storage and keep frozen items organized. It replaces broken or missing baskets so food stays contained and easier to access. What it does:

• Holds and organizes frozen foods to prevent items from shifting or falling
• Provides open wire construction for airflow around frozen goods
• Replaces damaged, bent, or missing freezer baskets
• Common symptoms it remedies: broken wires, basket missing, items sliding or not staying contained

• Typically slides into existing freezer rails or seats on support ledges; no special tools usually required
• Remove nearby shelves/drawers first for access
• Handle wire edges carefully; wear gloves if needed to avoid scratches
• Ensure basket is fully seated before loading and do not force or bend wires during install

This replacement cover hinge secures and pivots the appliance cover so the lid or top opens and closes smoothly. Restores proper alignment and support for safe, reliable operation. What it does:

• Provides a durable pivot point for the appliance cover or lid
• Replaces worn, cracked, or broken hinge that causes sagging or misalignment
• Helps eliminate rubbing, catching, or noisy operation when opening/closing
• Restores proper fit to prevent gaps and improve safety when the cover is closed

• One cover hinge

• Disconnect power before servicing
• Support the cover or lid while removing fasteners to prevent it from falling
• Use appropriate hand tools; retain original fasteners unless replacement hardware is supplied
• After installation, verify smooth operation and secure mounting before returning appliance to service

This foam insulation tube slips over refrigerator tubing to help reduce condensation and protect lines from moisture and minor abrasion. It's a simple replacement that restores padding and prevents dripping in affected areas. What it does:

• Insulates exposed tubing to reduce surface condensation and water buildup
• Cushions lines to help prevent chafing and minor damage
• Helps maintain a dry cabinet area by limiting drips from sweating lines
• Useful when original insulation is torn, compressed, or missing

• Disconnect power to the appliance before servicing; follow all safety guidelines
• Slide the foam sleeve over the tubing; trim to fit with a sharp blade if necessary
• Replace any damaged or brittle tubing discovered during install
• Do not use if foam is melted, charred, or contaminated

This factory screw secures panels, brackets, and other components inside your refrigerator. Replacing a missing or stripped fastener restores a tight fit, reduces vibration, and helps keep parts aligned so covers and assemblies stay in place.

• Fastens sheet-metal, plastic, and bracket assemblies to the cabinet or liner
• Replaces lost, corroded, or stripped hardware
• Can help address loose or rattling parts and minor misalignment
• Fits original threaded mounting points for a proper, secure hold

• Disconnect power; shut off water supply if working near water lines
• Match to the original location; start threads by hand to avoid cross-threading
• Tighten snugly only—overtightening can strip threads or crack plastic

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

This fixed freezer module shelf supports and secures the freezer module assembly, restoring stable storage and preventing items from shifting or contacting the module. It's a direct replacement for a cracked, warped, or missing shelf. What it does:

• Holds and supports the freezer module assembly so it stays properly positioned.
• Keeps stored items from contacting or damaging the module.
• Replaces shelves that are cracked, broken, or bent and that allow items to slide or fall.
• Reduces rattling or movement caused by a loose or broken shelf.

• Disconnect power to the refrigerator before servicing to prevent electrical hazard.
• Empty the freezer area and remove loose shelves or bins that block access.
• Align the shelf with its mounting points and seat it gently; do not force or modify the part.
• If fasteners are present, reuse OEM fasteners or replace with manufacturer-specified hardware.

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This replacement screw fastens refrigerator components such as brackets, panels, and handles. Replacing a missing or stripped fastener with the correct size helps restore a secure fit, proper alignment, and quieter operation.

• Secures brackets, trim, or handle assemblies to the cabinet or liner
• Replaces stripped, corroded, or missing hardware
• Helps reduce rattles and looseness from vibration
• Maintains proper alignment of attached parts

• Unplug the refrigerator and shut off the water supply before service
• Match thread size and length to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit for the head style; do not overtighten
• Reinstall any washers or spacers in the original order

This plenum fan moves cold air from the evaporator into the refrigerator cabinet to help maintain even temperatures and proper cooling performance. It's a direct-replacement evaporator air-moving component. What it does:

• Circulates cold air from the evaporator coil through the refrigerator compartments
• Helps the appliance reach and hold set temperatures for food safety
• Commonly associated with weak cooling, uneven temperatures, or excessive frost buildup when failing
• Works with the evaporator motor system to maintain proper airflow

• One plenum fan (evaporator) assembly

• Disconnect power to the appliance before beginning any repair
• Handle evaporator fins and fan blades carefully to avoid damage
• May require removing interior panels or the evaporator cover; use basic hand tools

Size: 8-32 t. Includes 12 screws.

This black cover hinge replaces a damaged or worn hinge cover to restore proper fit and appearance where the hinge mounts. It helps protect the hinge area and keeps the lid or top closing and opening smoothly. What it does:

• Covers and secures the hinge area to prevent wear and reduce rubbing or noise
• Helps keep the lid/top aligned for smooth opening and closing
• Restores finished appearance where the original hinge cover is cracked or missing
• Commonly used when the hinge cover is broken, loose, or causes wobble or misalignment

• Disconnect power to the appliance before servicing to avoid shock or injury
• Basic hand tools (screwdriver, socket) are typically required; keep removed fasteners for reinstallation
• Handle sharp edges carefully and support the lid/top during removal and installation