Gse25ghecss Parts

This interface dispenser assembly is the refrigerator's front dispenser control panel that accepts user selections and sends control signals for water and ice dispensing. It restores proper dispenser input and control when the panel fails. What it does:

• Accepts user input (buttons/switches) and communicates dispenser commands to the fridge control system
• Activates dispenser functions for water and ice selection and starts the dispense cycle
• Provides the visible control surface and indicator lights associated with the dispenser
• Often used when dispenser buttons are unresponsive, dispenser functions are intermittent, or indicators fail to light

• Disconnect power to the appliance and turn off the water supply before starting work
• Access typically requires removing the inner dispenser/door trim to unplug the assembly connectors; handle wiring and connectors gently
• Test dispenser operation before fully reassembling

This 3-way triple water valve controls water flow to the dispenser and ice maker on compatible refrigerators, restoring proper water delivery and preventing leaks when the valve fails. It replaces a worn or stuck valve assembly. What it does:

• Directs water to the ice maker, fresh-food dispenser and/or water filtration line as the refrigerator requests
• Opens and closes electrically to allow water flow when the dispenser or ice maker calls for water
• Common symptoms: no water to dispenser or ice maker, slow flow, intermittent flow, or active leaking at the valve
• Works with the refrigerator's inlet hose and internal water lines to route water where needed

• One triple (3-way) water valve assembly

• Turn off water supply and unplug the appliance before starting; relieve system pressure by running the dispenser briefly after shutoff
• Handle water lines and fittings carefully to avoid damage
• Tighten hose connections securely and check for leaks after restoring water and power

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

Fresh food side. Color: white. For the same part in black, purchase WR02X10779.

The Housing Shield Dispenser is an OEM replacement part for GE refrigerators. It is designed to cover and protect the dispenser housing to safeguard against spills, debris, and other external factors that could compromise the dispenser's interior.

A bad housing shield dispenser can occur due to wear and tear over time or damage caused by mishandling or accidents. If you notice symptoms such as leaks, dispenser malfunctions, or difficulty in dispensing water or ice, it may indicate a need to replace the housing shield dispenser.

Symptoms of a bad housing shield dispenser include:

• Leaks or drips from the dispenser area
• Inconsistent or insufficient dispensing of water or ice
• Difficulty in operating or using the dispenser

Restore your refrigerator's dispenser by replacing the faulty housing shield dispenser with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This replacement screw secures refrigerator panels, brackets, and trim to help keep components aligned and quiet. It matches the specified #8-18 thread and 1-1/2 inch length used at designated mounting points.

• Fastens panels, brackets, covers, and hardware as designed by the manufacturer
• Restores a missing or damaged fastener to keep parts secure and aligned
• Correct #8-18 tapping thread and 1-1/2 in. length for specified locations

• Unplug the refrigerator or disconnect power before servicing
• Wear cut-resistant gloves to protect from sharp edges
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any model-specific washers or clips originally installed on your unit

The Harness Cab Lower is an OEM replacement part for GE refrigerators. It sits behind the fresh food doors and contains wiring harnesses that power critical interior features.

Causes of a bad harness cab can include damaged insulation exposing wire fraying, breaks or crimps in wiring preventing power delivery, or short-circuits due to moisture over time. 

Symptoms include: 

• Lights, dispensers, or other interior components ceasing to operate properly
• Error codes or failure indications on control panels
• Buzzing or humming noises from wiring when functions are used

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This condenser assembly is the condenser coil used in compatible refrigerators to release heat from the refrigerant so the appliance can cool efficiently. Replacing a damaged coil helps restore proper cooling performance and energy use. What it does:

• Circulates refrigerant through the condenser coil to dissipate heat from the refrigeration system
• Supports normal compressor cycling and helps maintain steady internal temperatures
• Common symptom fixes: reduces long run times, improves inadequate or uneven cooling, and addresses overheating or noisy compressor operation
• Works with the condenser fan and other sealed-system components to complete the heat-exchange process

• Disconnect power to the refrigerator before servicing to avoid electric shock
• Access commonly from the rear lower panel or front grille; may require removal of kick plate or back cover
• Avoid damaging the coil fins; handle carefully and use fin comb if needed

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

This white stop door replaces the dispenser stop/door that controls access to the ice/water chute, helping restore proper dispenser operation and reduce sticking or unwanted discharge. Designed to match the original OEM fit and appearance. What it does

• Seals and releases the dispenser opening so ice or water is dispensed only when the door is actuated
• Replaces a cracked, warped, or jammed stop door that can cause sticking or partial openings
• Helps prevent accidental drips or debris entering the dispenser chute
• Restores a smooth, aligned door movement for reliable dispensing

• One white stop door

• Disconnect power to the appliance before starting any repair
• Remove dispenser housing or outer door per the service manual to access the stop door
• Inspect the actuator and mounting tabs for damage; replace if worn to ensure proper operation
• Use basic hand tools;

The Door Handle is an OEM component specifically designed for GE side-by-side refrigerators. This handle provides an ergonomic grip point for opening both the refrigerator and freezer doors. 

The handle is responsible for facilitating easy access to the entire fridge compartment. Its dual-purpose design allows for the convenient operation of both doors with a single touch.

Causes of a bad door handle can include wear and tear from frequent use over many years, as well as accidental impacts or bending from excessive force applied to open the doors.

Symptoms of a bad door handle include:

• Loose, unstable, or difficult to grip connection 
• Detachment from either door
• Chipping, cracking, or other signs of damage
• Inability to smoothly open one or both doors

Color: Stainless steel

Compatible also with Hotpoint, RCA, and select Kenmore refrigerator models.
 

This wire basket fits in the freezer compartment to restore usable storage and keep frozen items organized. It replaces broken or missing baskets so food stays contained and easier to access. What it does:

• Holds and organizes frozen foods to prevent items from shifting or falling
• Provides open wire construction for airflow around frozen goods
• Replaces damaged, bent, or missing freezer baskets
• Common symptoms it remedies: broken wires, basket missing, items sliding or not staying contained

• Typically slides into existing freezer rails or seats on support ledges; no special tools usually required
• Remove nearby shelves/drawers first for access
• Handle wire edges carefully; wear gloves if needed to avoid scratches
• Ensure basket is fully seated before loading and do not force or bend wires during install

This auger motor service kit restores the ice dispenser's drive so cubes move from the bin to the chute. Replace a weak or failed motor to bring back consistent ice dispensing and reduce humming or grinding noises.

• Powers the ice bucket auger/crusher to move ice through the dispenser chute
• Helps resolve: no ice dispensing, auger not turning, motor only hums or clicks
• Can reduce harsh grinding or buzzing during ice dispense
• Supports smooth, consistent delivery of cubed or crushed ice

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the auger motor area; note part orientation and wiring
• Transfer any reusable brackets or couplers as needed; seat the drive properly
• Check for ice buildup or a stripped coupling before reassembly; test dispense function

The Dispenser Interface & Board is an OEM part for GE refrigerators. This interface and board assembly is responsible for controlling the functions and features of the dispenser on your GE refrigerator, including ice dispensing, water dispensing, and temperature settings.

A bad dispenser interface and board can occur due to electrical issues, component failure, or other factors. If you notice symptoms such as unresponsive buttons, dispenser not working, or incorrect temperature readings, it may be time to replace the dispenser interface and board.

Symptoms of a bad dispenser interface and board include:

• Unresponsive buttons
• Dispenser not working
• Incorrect temperature readings

Restore the function of your GE refrigerator's dispenser by replacing the faulty dispenser interface and board with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This replacement cover hinge secures and pivots the appliance cover so the lid or top opens and closes smoothly. Restores proper alignment and support for safe, reliable operation. What it does:

• Provides a durable pivot point for the appliance cover or lid
• Replaces worn, cracked, or broken hinge that causes sagging or misalignment
• Helps eliminate rubbing, catching, or noisy operation when opening/closing
• Restores proper fit to prevent gaps and improve safety when the cover is closed

• One cover hinge

• Disconnect power before servicing
• Support the cover or lid while removing fasteners to prevent it from falling
• Use appropriate hand tools; retain original fasteners unless replacement hardware is supplied
• After installation, verify smooth operation and secure mounting before returning appliance to service

This foam insulation tube slips over refrigerator tubing to help reduce condensation and protect lines from moisture and minor abrasion. It's a simple replacement that restores padding and prevents dripping in affected areas. What it does:

• Insulates exposed tubing to reduce surface condensation and water buildup
• Cushions lines to help prevent chafing and minor damage
• Helps maintain a dry cabinet area by limiting drips from sweating lines
• Useful when original insulation is torn, compressed, or missing

• Disconnect power to the appliance before servicing; follow all safety guidelines
• Slide the foam sleeve over the tubing; trim to fit with a sharp blade if necessary
• Replace any damaged or brittle tubing discovered during install
• Do not use if foam is melted, charred, or contaminated