Gslj25fxb Parts

8-18 CA HX 1/2 S

Color: white. Measures about 17 inches wide by 1 inch deep.

This condenser assembly is the condenser coil used in compatible refrigerators to release heat from the refrigerant so the appliance can cool efficiently. Replacing a damaged coil helps restore proper cooling performance and energy use. What it does:

• Circulates refrigerant through the condenser coil to dissipate heat from the refrigeration system
• Supports normal compressor cycling and helps maintain steady internal temperatures
• Common symptom fixes: reduces long run times, improves inadequate or uneven cooling, and addresses overheating or noisy compressor operation
• Works with the condenser fan and other sealed-system components to complete the heat-exchange process

• Disconnect power to the refrigerator before servicing to avoid electric shock
• Access commonly from the rear lower panel or front grille; may require removal of kick plate or back cover
• Avoid damaging the coil fins; handle carefully and use fin comb if needed

Includes 12 screws. Size: 8-18 ab.

This top-closed thimble is a small protective plug that presses into a cabinet opening to cap and finish the hole, helping prevent abrasion and limiting air or moisture leaks for reliable appliance performance.

• Caps and seals an unused hole/opening in the liner or cabinet
• Shields edges to help protect nearby wiring or tubing from chafing
• Helps reduce drafts and moisture migration that can contribute to frost, condensation, or temperature swings
• Replace if cracked, brittle, loose, missing, or if you notice gaps or rubbing noises

• Disconnect power; if applicable, turn off the water supply
• Access the opening, remove the old thimble/plug, and clean the area
• Align and press the new thimble into the hole until fully seated and flush; avoid pinching wires or tubing
• Restore power/water and verify a snug fit

This hinge cover screw fastens the hinge cover in place, helping keep it secure and protecting the hinge components beneath. Replace a missing or stripped screw to stop the cover from loosening or rattling.

• Secures the hinge cover to the door/cabinet hinge
• Helps protect hinge hardware and wiring under the cover
• Replaces stripped, rusted, or missing hardware
• Common symptoms: loose or missing hinge cover, vibration or rattling at the hinge area

• Disconnect power to the appliance before servicing near the hinge area
• Use the correct screwdriver; start threads by hand to avoid cross-threading
• Align the cover properly and tighten snugly—do not overtighten to prevent stripping
• Keep the door closed during work to minimize movement

Handle fastener secures the appliance handle to the door or drawer, restoring a stable, tight fit. Replace a missing or loose fastener to stop the handle from wobbling or detaching during normal use. What it does:

• Secures the handle to the appliance door or drawer so the handle stays tight and stable.
• Replaces missing, stripped, or damaged handle screws/fasteners.
• Stops handle wobble and reduces the chance the handle will come off when pulled.
• Use when the handle feels loose, moves excessively, or falls off.

• Use the correct screwdriver or nut driver and hold the handle in position while tightening.
• Tighten until snug but do not overtighten; excess force can strip threads or crack plastic.
• If the handle is part of an electrical or sealed assembly, disconnect power and follow manufacturer service instructions before servicing.
• Refer to your appliance owner's manual or OEM instructions for model-specific placement and fastening details.

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

Rear evaporator fan motor bracket secures the evaporator fan motor to the refrigerator cabinet, maintaining airflow over the coils for efficient cooling. Replaces a bent or broken mounting bracket so the fan runs steadily. What it does:

• Holds the evaporator fan motor in the correct position to maintain steady rotation and consistent airflow across the evaporator coils.
• Prevents the motor from rubbing against the housing or fan blades, reducing noise and vibration.
• Common replacement when bracket is cracked, corroded, or bent — symptoms include noisy fan operation, intermittent fan movement, or reduced cooling performance.
• Restores proper motor alignment to help prevent premature motor wear.

• Always disconnect power to the appliance before beginning any repair.
• Remove the evaporator cover or access panel to reach the bracket; retain original mounting hardware unless replacements are provided.
• Ensure the fan blades spin freely and the motor is undamaged before reassembly; ensure the bracket seats securely and the fan does not contact the housing.
• If the motor or fan blade shows damage, replace those parts separately rather than relying on the bracket alone.

Right hand side

This replacement cover hinge secures and pivots the appliance cover so the lid or top opens and closes smoothly. Restores proper alignment and support for safe, reliable operation. What it does:

• Provides a durable pivot point for the appliance cover or lid
• Replaces worn, cracked, or broken hinge that causes sagging or misalignment
• Helps eliminate rubbing, catching, or noisy operation when opening/closing
• Restores proper fit to prevent gaps and improve safety when the cover is closed

• One cover hinge

• Disconnect power before servicing
• Support the cover or lid while removing fasteners to prevent it from falling
• Use appropriate hand tools; retain original fasteners unless replacement hardware is supplied
• After installation, verify smooth operation and secure mounting before returning appliance to service

This foam insulation tube slips over refrigerator tubing to help reduce condensation and protect lines from moisture and minor abrasion. It's a simple replacement that restores padding and prevents dripping in affected areas. What it does:

• Insulates exposed tubing to reduce surface condensation and water buildup
• Cushions lines to help prevent chafing and minor damage
• Helps maintain a dry cabinet area by limiting drips from sweating lines
• Useful when original insulation is torn, compressed, or missing

• Disconnect power to the appliance before servicing; follow all safety guidelines
• Slide the foam sleeve over the tubing; trim to fit with a sharp blade if necessary
• Replace any damaged or brittle tubing discovered during install
• Do not use if foam is melted, charred, or contaminated

This mobility front assembly replaces the worn front caster/roller that helps a refrigerator glide when pulled out for cleaning or service. Restores smooth forward movement and stable front support for safe access. What it does:

• Provides a rolling front support so the appliance moves smoothly on the floor
• Helps stabilize the front of the refrigerator when it is pulled out or pushed in
• Reduces sticking and uneven movement caused by worn or damaged rollers
• Can help minimize scraping or surface damage during repositioning

• One mobility front assembly

• Disconnect power and, if applicable, water supply before servicing
• Empty or secure loose items and have a second person help when tilting or moving the appliance
• Remove the kickplate or access panel as required to reach and replace the front assembly
• Tighten fasteners to OEM torque and test mobility before returning the appliance to normal use

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

Evaporator cover gasket creates a moisture- and air-sealing barrier between the evaporator cover and freezer liner to help reduce frost buildup and improve cooling consistency. Replacing a worn gasket helps prevent ice accumulation and water leaks. What it does:

• Seals the evaporator cover to minimize moisture intrusion and air leakage into the evaporator area.
• Helps reduce frost and ice buildup on the evaporator and freezer walls.
• Can help address symptoms such as excess frost, water pooling in the freezer, or uneven/freezer temperatures.
• Restores proper evaporator cover fit for more consistent defrost performance.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the evaporator cover per your model's service instructions, remove the old gasket, and clean the mating surfaces before installing the new gasket.
• Seat the gasket fully around the cover; some models use clips or adhesive.
• After reassembly and power-up, monitor the freezer for proper sealing, frost control, and any signs of leaks.

This is the dispenser ice bucket that holds and delivers ice from the freezer to the dispenser chute, restoring reliable ice storage and delivery for compatible refrigerators. Durable molded design helps contain and release cubes cleanly. What it does:

• Holds ice produced by the icemaker so cubes can move to the dispenser
• Guides ice toward the dispenser chute for consistent delivery
• Helps prevent ice from spilling into the freezer compartment
• Worn, cracked, or warped buckets can cause jams or poor dispensing

• Disconnect power to the refrigerator before servicing to avoid injury
• Remove existing ice and any obstructions before installing the new bucket
• Align bucket tabs/slots with tracks in the freezer dispenser area and slide into place until seated
• If ice jams or dispensing issues persist after installation, also inspect the auger/drive components and icemaker