Gtd65debsj3ws Parts

This complete door assembly replaces a damaged or non-closing door to restore proper sealing and safe operation. It provides the outer panel, inner panel, and hardware needed for a factory-style repair. What it does

• Replaces cracked or broken door panels and visible damage that prevents normal use
• Restores proper door alignment and sealing to help the appliance close and latch correctly
• Replaces worn or loose hinges and mounting points that cause sagging or uneven gaps
• Stops drafts, light leaks, and helps maintain internal temperature by restoring a solid door fit

• One complete door assembly

• Disconnect power (and water, if applicable) before starting any repair
• Handle glass components carefully; wear gloves and eye protection to avoid injury
• Door assemblies are often heavy or awkward — a second person may be needed for safe alignment
• Follow manufacturer instructions for correct torque and seal seating

This motor support is the stamped metal bracket that secures the dryer motor and blower assembly, keeping components aligned for smooth operation. It restores proper motor mounting and reduces noise from loose or misaligned parts. What it does:

• Holds the dryer motor and blower housing in the correct position to prevent wobble or misalignment
• Helps maintain proper blower alignment for effective air movement
• Supports safe, reliable motor operation when the original bracket is bent, cracked, or worn

• Disconnect power (unplug electric or shut off gas and breaker) before beginning repair
• Access requires opening the dryer cabinet and removing the drum and/or front panel on many models
• Inspect related components (motor mounts, blower wheel, idler, belt) and replace if damaged

A replacement silicon controlled rectifier (SCR) that restores electronic power switching in the appliance's control circuitry. This SCR provides reliable on/off switching for motors or heating circuits when the original SCR has failed. What it does:

• Acts as an electronic switch to control power delivery to heating elements or motors
• Commonly fails when the appliance has no heat, intermittent operation, or won't run consistently
• Replaces a burned, shorted, or open SCR to restore normal control-board switching behavior
• Helps stop arcing or erratic performance when the original semiconductor has degraded

• For safety, disconnect power before accessing control electronics or replacing the SCR
• Handle the SCR and circuit board carefully to avoid ESD damage; use proper grounding if available
• Verify correct orientation and secure mounting; ensure all wiring and connectors are seated properly

This drum assembly is the rotating tub that holds and tumbles clothes in the dryer, restoring proper load rotation for efficient drying and gentle fabric handling. It replaces a worn or damaged drum to eliminate rubbing and uneven tumbling. What it does

• Provides the rotating drum surface for clothes to tumble during a dry cycle
• Restores smooth rotation if the original drum was dented, cracked, or worn
• Addresses rubbing, scraping, or fabric-catching noises caused by drum damage
• Helps correct uneven tumbling or garments sticking to the drum surface

• One drum assembly

• Disconnect power (and gas, for gas dryers) before beginning service
• Drum assemblies are heavy and may require two people to remove and install safely
• Inspect or replace related parts (belt, rollers, idler, seals) if they show wear

Includes 12 screws.

This idler support bracket holds the dryer idler pulley in the correct position so the drive belt stays routed and tensioned, helping the drum turn smoothly. It replaces a worn or broken bracket to restore proper belt alignment and reduce belt slippage. What it does:

• Secures the idler pulley to the dryer chassis so the drive belt maintains correct tension
• Keeps the belt aligned to prevent rubbing, squealing, or premature wear
• Helps the drum turn freely by maintaining consistent belt routing and tension
• Commonly replaced when the bracket is cracked, bent, or the idler pulley mounting fails

• One idler support bracket

• Disconnect power before starting any repair
• Access typically requires removing the dryer's front or lower access panel; follow model-specific disassembly steps
• Inspect the idler pulley and drive belt; replace any worn components together to ensure reliable operation
• Use basic hand tools; avoid forcing fasteners and follow torque/fastening recommendations in the service manual

This backsplash assembly replaces the rear backguard on electric and gas ranges to restore a clean finished appearance and protect the wall and control-area wiring. It provides a durable mounting surface for controls, trim, and wiring covers. What it does:

• Covers the rear wall area behind the cooktop, preventing heat and grease from reaching the wall
• Serves as the mounting panel for the control cluster, clock and wiring harness tie points
• Restores a finished look after damage or corrosion to the original backguard
• Commonly replaces units that are dented, cracked, rusted, or have broken mounting tabs

• One backsplash assembly

• Disconnect power before beginning any service
• Handle the panel carefully to avoid bending or scratching painted surfaces; some installations require transferring controls or trim
• Have a second person or appropriate lifting support for safe alignment and mounting
• Use existing hardware only if undamaged; for correct reassembly steps