Gtup27oemoww Parts

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

This front panel assembly replaces a damaged or worn control-panel face to restore the appliance's front appearance and provide a secure mounting surface for controls. It keeps the control area sealed and looking factory-fresh. What it does:

• Replaces the visible front/control panel to cover and protect underlying controls and electronics
• Provides a mounting surface for buttons, knobs, or the touch-control interface
• Helps prevent dirt, grease, and moisture from reaching internal components
• Common repair for cracked, discolored, or broken control-face panels

• One front panel assembly as shown

• Installation requires removing the range/oven console and disconnecting power first — disconnect power at the breaker or unplug the appliance
• Handle panels and clips carefully to avoid damaging trim tabs or painted surfaces
• Use proper fasteners and alignment during reassembly; verify controls and display function before returning the appliance to service
• Label connections and take photos for reference

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

This stop-drain hose routes and drains water from the appliance to the drain or pump, helping prevent standing water and improper drainage. Replaces a worn, cracked, or leaking drain hose to restore proper water flow. What it does

• Channels discharged water from the appliance to the drain/pump assembly.
• Stops leaks caused by split, brittle, or collapsed hose sections.
• Helps restore normal draining when water pools in the tub or cabinet.
• Reduces the chance of water damage from a failed hose connection.

• Disconnect power and shut off the water supply before beginning any work.
• Remove old hose and inspect fittings; replace clamps if corroded or damaged.
• Route hose without sharp bends or kinks and secure with the factory clamps or equivalent.
• After installation, run a short cycle and check all connections for leaks.

This duct exhaust directs and channels appliance exhaust air to the venting system to help remove heat, steam and odors from the unit. Fits into the appliance's vent path to restore proper airflow and venting performance. What it does:

• Channels exhaust air from the appliance to the household venting system
• Restores a sealed outlet path to reduce backflow and poor venting
• Helps prevent overheating and moisture buildup in the appliance cabinet area
• Commonly replaced when the existing duct is cracked, warped or missing

• Disconnect power and gas (if applicable) before servicing; follow manufacturer safety instructions
• Verify orientation and seating into the appliance vent before tightening fasteners
• Use proper venting materials and clamps when reconnecting to the home vent system

This control panel front is the exterior cover for the appliance's electronic control area, restoring the unit's finished appearance and protecting buttons and displays from dirt and damage. It's a direct-fit cosmetic and protective replacement. What it does:

• Covers and protects the appliance control keypad and display from spills, dust, and wear
• Provides the correct surface for buttons and touch controls to operate properly
• Restores the appliance's original look when the factory panel is cracked, scratched, or discolored
• Helps prevent moisture and debris from reaching internal electronics

• High-level replacement: remove power and access the control housing before swapping panels
• Typical procedure: detach outer trim or bezel, remove fasteners holding the old panel, transfer any mounted buttons or overlays, then secure the new panel
• Use caution around glass, sharp edges, and wiring; avoid forcing connectors

This is a replacement 8-18 threaded hex-washer-head screw (3/8" length, zinc finish) used to secure panels and components on compatible appliances. It restores proper fit and stops rattling or loose parts. What it does

• Fastens panels, brackets, or assemblies where an 8-18 threaded screw is specified
• Replaces missing or damaged screws that cause loose panels or vibration
• Restores secure mounting for trim, brackets, or internal components
• Matches OEM head style and finish for correct fit and appearance

• One replacement screw (8-18 x 3/8", hex washer head, zinc)

• Disconnect power and water before starting any repair
• Use the correct driver or bit to avoid stripping the head
• Do not overtighten; snug to secure components without deforming parts
• If other fasteners are damaged, replace them with identical OEM parts

This overflow elbow is a small drain fitting that routes excess water away from the appliance to prevent spills and water damage. It restores proper overflow/drain flow so the unit can safely divert unwanted water. What it does:

• Directs overflow or drain water from the appliance plumbing to the drain path
• Replaces cracked, clogged, or leaking elbows that can cause pooling or leaks
• Helps restore normal draining behavior and reduces risk of water where it shouldn't be
• Fits into the appliance's existing drain/overflow tubing and connections

• One overflow elbow

• Inspect surrounding hoses and clips; replace any damaged components for a reliable repair
• Disconnect power and water supply before beginning work to avoid electrical shock or flooding
• Use appropriate clamps or fittings to ensure a secure, leak-free connection

A hinge bushing that helps the appliance door pivot smoothly and maintain proper alignment. Replacing a worn bushing restores stable door operation and reduces sticking, noise, and uneven closing. What it does:

• Provides a low-friction pivot surface for a door hinge
• Keeps the door aligned to prevent sagging or gaps when closed
• Reduces squeaks, binding, and irregular movement at the hinge
• Helps extend hinge and door hardware life by minimizing metal-on-metal wear

• One hinge bushing

• Disconnect power and remove or support the door before working on hinges
• Inspect hinge and surrounding hardware; replace any damaged components to ensure proper fit
• Install with correct orientation; do not force parts—misalignment can cause premature wear
• Use basic hand tools; follow OEM service instructions if available

A left-side hinge washer cover that restores the washer lid hinge's appearance and helps protect the hinge assembly from dirt and wear. Fits where the hinge meets the cabinet to keep the hinge area covered and tidy. What it does:

• Covers and protects the left lid hinge area from debris and abrasion
• Helps prevent direct metal-to-metal contact that can accelerate wear
• Restores finished appearance after a cracked or missing cover
• Can reduce rubbing noises caused by an exposed hinge

• Disconnect power to the appliance before servicing to avoid injury
• Usually installs by snapping or securing over the left hinge; remove hinge fasteners only if necessary
• Inspect hinge and surrounding parts for damage before reassembly
• Do not force plastic parts into place; replace if cracked or deformed