Gtw46oasj6ww Parts

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

This wire harness connects your washer's control to two water valves, supplying power so they open and close at the right times. Replacing a damaged harness restores dependable water flow during fill and rinse cycles.

• Carries electrical power/signals from the control to both water valves
• Ensures valves actuate correctly during fill operations
• Helps resolve no-fill, partial/intermittent filling, or one valve not activating
• Clears valve-circuit error codes or issues from loose, burnt, or broken connectors

• Unplug the washer before servicing; turn off water supply if moving hoses
• Note/photograph original routing and connector locations; move any clips/retainers to the new harness
• Seat connectors fully on the valve solenoids; do not force—align keys to avoid pin damage
• Inspect valve coils and connector pins for heat damage or corrosion and address as needed

The Clamp is an OEM part for GE washers. It is used to securely fasten critical components like hoses, sensors, and wiring harnesses in place inside the washer cabinet. 

As a machine that handles water, chemicals, and moving parts, a washer requires many clamps to organize its internal systems. They ensure hoses and electrical wiring remain properly positioned and protected throughout years of operation. Without solid clamps, connections could loosen or detach, leading to leaks or electrical faults.

Causes of a bad clamp can include fatigue from constant vibration, outright breakage from impact or tension overload, or rust/corrosion damage over extended use. 

Symptoms of a failed clamp include:

• Loose, disconnected or damaged hoses and wiring  
• Water leaks from hose connections
• Electrical or sensor errors

The clamp is also compatible with some Kenmore and other brands that use GE components.

White top cover that protects the appliance's internal components while restoring a clean, finished appearance. Fits over the control area to help keep wiring and switches covered and reduce dirt and debris intrusion. What it does:

• Shields internal wiring, terminals and control components from spills, debris and everyday wear.
• Provides a finished surface and helps secure the control-panel area.
• Replacing a cracked, warped or missing top cover prevents exposed parts and improves safety and appearance.
• Matches white finish for a like-for-like cosmetic replacement.

• Always disconnect power to the appliance before beginning any service.
• Remove control knobs and any trim or fasteners that hold the top cover in place; follow the appliance's service manual for step-by-step removal.
• Handle edges carefully to avoid cuts or damage; check that mounting tabs and screws seat correctly during reinstallation.
• After installing, restore power and verify controls and any related components operate normally.

This 10-32 hex head screw secures appliance panels and components where a small machine screw is required. It provides a durable, threaded fastening point for repair or reassembly. What it does:

• Fastens panels, brackets, and small components using a 10-32 machine thread
• Hex head accepts a 7/16" socket or wrench for positive torque application
• Replaces worn or damaged screws that cause loose or rattling parts
• Compatible with common metal-to-metal and tapped-hole connections

• One 10-32 hex head screw with 7/16" socket head

• Use the correct 7/16" socket or wrench to avoid rounding the head
• Thread engagement should match the appliance's threaded insert; do not force if resistance is felt
• Follow manufacturer service manual for torque specs and installation sequence
• Disconnect power and follow safety procedures before servicing the appliance

This clip spring cover is a small plastic retainer that secures the spring/clip assembly on compatible appliances, helping keep moving parts aligned and reducing rattles or loose components. Replaces a worn or broken cover to restore proper fit. What it does

• Covers and holds a spring or clip in place to prevent displacement during operation
• Keeps assemblies aligned to reduce noise and intermittent part contact
• Helps maintain consistent tension where a spring or clip is used
• Commonly replaced when the original cover is cracked, broken, or missing

• One clip spring cover

• High-level replacement; basic hand tools may be required to access the location
• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Inspect adjacent springs/clips for wear and replace if damaged

8-18 hi/lo 5/8

This white control panel replaces a worn or damaged console face to restore your range's front appearance and button access. It provides the exterior surface and button openings used with the oven control assembly and keypad. What it does

• Covers and protects the oven control electronics while providing button and display openings
• Restores a cracked, discolored, or scratched front surface that affects usability or appearance
• Helps ensure buttons and touchpads line up correctly with the underlying control module
• Can reduce light leaks and prevent debris from entering the control area

• Disconnect power to the appliance before starting any work to avoid shock
• Remove the oven console screws and trim to access and replace the panel; retain all fasteners
• Handle edges and any glass or plastic surfaces carefully to avoid cracking or scratching
• If the keypad or control module must be detached, follow OEM instructions.

This wireform hinge is the right-side lid hinge that supports and guides the washer lid for smooth opening and closing, restoring proper lid alignment and operation. It's a direct-fit replacement when the original hinge is bent or worn. What it does

• Secures the right side of the lid to the cabinet so the lid opens and closes reliably
• Restores proper lid alignment and prevents the lid from sagging or catching
• Reduces noise and grinding caused by a bent or loose hinge
• Helps the lid stay in the correct open/closed position during use

• One right-side wireform lid hinge

• Unplug the appliance and turn off water supply before starting
• Support the lid while removing and installing the hinge to prevent dropping or damage
• Basic hand tools typically required; follow OEM diagram for correct fastener locations
• If both hinges show wear, replace both sides for balanced operation

This replacement screw fastens appliance panels, brackets, and trim. The 8-18 thread with 1-3/4-inch length provides reliable bite in sheet metal or plastic, restoring a secure fit when an original fastener is missing or damaged.

• Secures panels, brackets, and trim to the cabinet or frame
• Replaces lost, stripped, or corroded fasteners
• Helps address loose or rattling panels, minor gaps, or misalignment
• Appropriate for sheet-metal applications that require ~1-3/4-inch reach

• Disconnect power before servicing; wear cut-resistant gloves
• Support the panel or part being fastened and use the correct driver for the screw head
• Start threads by hand to avoid cross-threading; do not overtighten into plastic or thin metal
• Repair or replace the anchor before installing

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This main wiring harness (green) routes power and signals between an appliance's control and major components, restoring reliable electrical connections. Replacing a damaged harness helps stop intermittent power issues and restore normal operation. What it does

• Connects control board to motors, switches, and sensors to enable normal operation
• Replaces frayed, burnt, or broken wiring that can cause intermittent or complete loss of function
• Helps eliminate electrical shorts or open circuits that prevent the appliance from starting or running consistently
• Maintains OEM-style connectors and color coding for proper routing and reconnection

• Always disconnect power (unplug or switch off circuit breaker) before servicing electrical components
• Route and secure the harness per OEM clips/retainers to avoid pinching or rubbing

This silicon controlled rectifier (SCR) switches and regulates power in compatible appliance control circuits, helping the unit deliver correct power to heating elements or motors. It's a direct replacement component when the original SCR fails. What it does

• Acts as a solid-state switch that controls current flow to heating elements, motors or other high-current circuits.
• Fails open or shorted when worn; common symptom is loss of heating, intermittent power to the controlled component, or no operation on affected circuits.
• Provides fast, repeatable switching compared with electromechanical relays.
• Designed for stud-mount installation with insulated/marked terminals for correct wiring.

• One silicon controlled rectifier (SCR) as listed.

• Disconnect all power before accessing or replacing the SCR to avoid shock or equipment damage.
• Note terminal orientation and wiring before removal; replace with the same terminal/stud configuration.
• Avoid electrostatic discharge to the replacement part; handle by the body and avoid touching terminals.