Gud27gssjoww Parts

A left-side hinge washer cover that restores the washer lid hinge's appearance and helps protect the hinge assembly from dirt and wear. Fits where the hinge meets the cabinet to keep the hinge area covered and tidy. What it does:

• Covers and protects the left lid hinge area from debris and abrasion
• Helps prevent direct metal-to-metal contact that can accelerate wear
• Restores finished appearance after a cracked or missing cover
• Can reduce rubbing noises caused by an exposed hinge

• Disconnect power to the appliance before servicing to avoid injury
• Usually installs by snapping or securing over the left hinge; remove hinge fasteners only if necessary
• Inspect hinge and surrounding parts for damage before reassembly
• Do not force plastic parts into place; replace if cracked or deformed

This inner wash basket replaces a damaged or worn tub to restore proper clothes movement and water drainage during a wash cycle. It keeps laundry contained while the washer agitates and spins. What it does:

• Holds and supports clothing during fill, wash and spin cycles
• Allows water to pass through for effective rinsing and draining
• Maintains proper balance and rotation of the wash load
• Replaces baskets that are bent, cracked, corroded or causing unusual noise/vibration

• Disconnect power and shut off water before servicing
• Inspect seals, bearings and mounting hardware; replace worn components as needed
• Heavy part—use two people or appropriate lifting tools to avoid injury
• Refer to the washer's service manual for disassembly/reassembly steps and torque specifications

This is a #8-18 by 5/8-inch Torq II-head screw used to secure appliance panels and components. It provides a reliable fastener option when replacing stripped or missing screws to restore proper fit and reduce vibration or rattling. What it does:

• Secures trim, panels, brackets or small components to appliance frames
• Restores proper alignment and reduces noise from loose parts
• Replaces worn, stripped, or missing fasteners to prevent further damage
• Compatible where an 8-18 thread and 5/8" length with a Torq II-style head are specified

• One screw

• Use the correct Torq II driver bit to avoid cam-out or head damage
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• If replacing rusted or stripped screws, inspect mating threads and replace as needed
• Disconnect power and follow appliance safety instructions before servicing

This motor bracket secures the appliance motor to the housing so the motor stays aligned and stable during operation, helping maintain proper drive function and reduce vibration. What it does

• Provides a secure mounting point for the motor to keep correct alignment with belts or shafts
• Reduces motor movement and vibration that can cause noise or wear
• Helps maintain proper drive geometry to support consistent operation
• Commonly replaced when the original bracket is cracked, bent, or broken

• One motor bracket

• Disconnect power before starting any repair to avoid electrical shock
• Inspect mounting hardware and surrounding components; replace any damaged fasteners
• Tighten fasteners to the manufacturer's specification and verify motor alignment before testing

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly

A small replacement hose clip that secures flexible appliance hoses to fittings to help prevent leaks and disconnections. Fits commonly used appliance hose connections to restore a secure seal and reliable water flow. What it does:

• Secures a water or drain hose to a barb or fitting to prevent the hose from coming loose
• Helps stop leaks and drips caused by loose or slipping hoses
• Prevents hose movement and rubbing that can lead to wear or abrasion
• Useful when a hose slips off during operation or after maintenance

• Disconnect power and shut off the water supply before servicing the appliance
• Use appropriate hand tools (needle-nose pliers or hose clamp pliers) to open and seat the clip
• Position the clip over the fitting and tighten until the hose is snug and secure; avoid over-tightening
• Replace only with the correct OEM-style clip for a proper fit