Hbl0 Parts

This factory fixing kit provides the mounting hardware needed to secure the applicable component or panel on your appliance. Replacing worn or missing fasteners restores proper alignment and a solid, rattle-free installation.

• Secures panels, brackets, or trim to the appliance chassis or door
• Helps prevent shifting, vibration, and rattling during operation
• Restores correct alignment and fit when hardware is missing or stripped
• Useful during initial installation or when re-installing serviced parts

• Disconnect electrical power; if your appliance is plumbed, shut off water before servicing
• Follow your model's installation/service instructions for exact hardware locations and orientation
• Tighten hardware evenly; do not overtighten to avoid damaging plastic or sheet metal
• Verify alignment and smooth operation before restoring power and/or water

This door latch secures the appliance door and helps enable normal operation by keeping the door closed and latched during cycles. Replacing a worn or broken latch restores proper door engagement and reliable start/lock behavior. What it does:

• Secures the door closed so the appliance can run and complete cycles
• Engages with the strike to maintain a tight, consistent seal during operation
• Helps the control detect a closed/locked door and permit cycle start
• Commonly replaced when the door won't stay closed, won't lock, or the unit won't start

• One replacement door latch

• Disconnect power and water before beginning any repair
• Access may require removing the inner door panel or front trim—keep fasteners organized
• Verify alignment of the latch and strike before reassembly to ensure proper engagement
• If the latch has electrical connectors, reconnect securely and avoid pinching wires

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

This is a replacement nut used to secure internal appliance components. It restores proper fastening so assemblies stay tight and reduces noise or movement caused by loose hardware. What it does:

• Secures brackets, trim or internal components to prevent parts from shifting
• Stops rattling or vibration caused by a missing or loose nut
• Restores proper fastening after maintenance or repair
• Helps maintain correct alignment of the secured component

• Disconnect power and water before accessing internal parts
• Use appropriate hand tools and a firm grip; avoid power tools that can over-torque
• Do not overtighten — snug until secure to avoid stripping threads
• Replace any corroded or damaged mating hardware for a lasting repair

This metal mounting bracket secures internal components and panels to restore proper alignment and reduce rattling. It's a straightforward replacement part that helps keep appliance panels and assemblies firmly in place for reliable operation. What it does:

• Provides a secure attachment point for panels or internal assemblies to prevent movement and vibration
• Helps correct alignment issues that can cause rubbing, gaps, or noise
• Restores the original fit where a bent, cracked, or missing bracket caused loose parts
• Works with the appliance's existing fasteners and mounting points

• Remove power and, if applicable, disconnect the appliance from water before beginning work
• Use the factory fasteners or OEM replacement screws to secure the bracket in the original location
• Verify alignment of the attached panel or assembly before fully tightening fasteners

This cap is a direct-fit replacement closure used to protect and seal an exposed opening or component on compatible Bosch appliances, preventing dirt, moisture and damage for reliable operation. What it does:

• Covers and seals an exposed port or fastener to keep contaminants out
• Protects internal components from moisture and debris that can cause malfunctions
• Replaces cracked, warped or missing caps that allow leaks or debris intrusion
• Restores proper fit and appearance where a damaged cap leaves an opening

• Disconnect appliance power and water supply before starting any repair
• Verify the cap matches the damaged/original part before installation
• Press or snap the cap into place until fully seated; do not force or pry
• Inspect mating surfaces for damage or debris and clean before installing

The Control Module is an OEM part for Bosch ranges that regulates various functions of your oven, including temperature settings, timer functions, and cooking modes.

A bad control module can occur due to electrical malfunctions, power surges, or damage from excessive heat or moisture. Signs of a faulty control unit include the oven not responding to commands, error messages on the display, or erratic temperature fluctuations.

Symptoms of a bad control module include:

• Unresponsive oven controls
• Error messages displayed 
• Inaccurate temperature readings

Replace your malfunctioning control module with this genuine OEM Bosch part to restore your range oven's functions. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This support mounting bracket secures internal components to the appliance frame, restoring proper alignment and stable operation. It replaces a worn, broken, or loose support to help reduce rattling and prevent component sag. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Re-establishes correct alignment when a bracket is bent or broken
• Helps reduce vibration and rattling caused by loose or damaged supports
• Commonly replaced when a component shifts, rubs, or no longer sits flush

• Disconnect power and water before starting any repair.
• Basic hand tools are typically required; follow OEM service instructions for disassembly/reassembly.
• Inspect adjacent fasteners and clips; replace any that are damaged to ensure a secure fit.

This trim plate is a decorative panel that restores the finished look of the appliance opening and helps cover gaps around the control or access area. It provides a clean, factory appearance and prevents dirt from collecting in the seam. What it does:

• Covers and finishes the edge of an opening or control area for a seamless appearance
• Helps keep crumbs, dust and spills from entering gaps around the appliance face
• Replaces bent, scratched or discolored trim that affects the appliance look
• Restores proper alignment where a damaged trim creates visible gaps

• One trim plate

• Disconnect power to the appliance before attempting removal or installation
• Handle carefully to avoid scratching the finished surface; use soft gloves if available
• Retain any mounting screws or clips from the original trim and reuse if appropriate

This mounting bracket secures appliance panels or components in place to restore proper fit and stable operation. A simple replacement when a broken or bent bracket causes rattling, misalignment, or loose panels. What it does

• Provides structural support to hold panels, trim, or assemblies in position
• Prevents rattling and vibration from a loose or damaged bracket
• Restores proper alignment of the attached component for normal operation
• Can fail from bending, cracking, or fastener loss, leading to gaps or movement

• One mounting bracket

• Disconnect power and shut off water before starting any repair
• Use appropriate tools to remove fasteners; keep track of mounting screws or clips
• Inspect surrounding parts and fasteners for damage; replace any stripped hardware
• Handle sharp edges carefully and test fit before reassembly