Htw200askww Parts

This 6-32 machine flat-head hinge lid screw secures the lid hinge on compatible GE appliances, restoring proper lid alignment and smooth opening and closing. A simple replacement that addresses loose or rattling lids. What it does

• Fastens the lid hinge to the cabinet or hinge assembly
• Keeps the lid aligned for smooth opening and closing
• Helps stop lid wobble, rattling or uneven seating
• Replaces worn, stripped, or missing hinge screws

• One 6-32 machine flat-head hinge screw

• Turn power off and unplug appliance before servicing
• Use the correct-size screwdriver or nut driver to avoid stripping the head
• Thread screw in by hand to start, then tighten snugly—do not over-torque
• Check hinge alignment and lid operation after installation

This control board shield protects the appliance's electronic control board from debris, heat, and accidental contact to help maintain reliable operation. It's a direct-fit replacement designed to restore proper protection for the control electronics. What it does:

• Covers and shields the electronic control board from dust, moisture splash, and physical contact
• Helps reduce risk of short circuits caused by loose debris or small objects
• Preserves board components from incidental heat exposure and wear
• Commonly replaced when the old shield is cracked, broken, or missing

• One control board shield

• Disconnect power before servicing to avoid shock or damage to electronics
• Handle shield and control board carefully to avoid bending tabs or damaging connectors
• Reuse original fasteners if undamaged; replace any broken clips or screws

This tub cover is a replacement interior cover that protects the washer tub assembly and helps maintain proper water flow and cleaning performance. It restores the tub's sealing and shielding where the original cover is cracked or missing. What it does:

• Protects the tub assembly and internal components from debris and direct spray
• Helps maintain proper water flow patterns for consistent cleaning
• Reduces the chance of parts rubbing against the tub and causing noise or damage
• Commonly replaced when the cover is cracked, warped, or shows visible wear

• Disconnect power to the appliance before beginning any work
• Turn off water supply and drain the tub if applicable
• Basic hand tools required; follow OEM disassembly steps for access
• Handle carefully—edges may be sharp and proper alignment is required for a correct fit

This hex-head machine screw secures appliance panels and internal components where a 5/16-24 x 1 inch fastener is required. Durable replacement for stripped or missing screws to restore safe assembly and reduce vibration. What it does:

• Fastens panels, brackets, and assemblies with a 5/16-24 machine thread.
• Replaces worn, stripped, or missing screws that can cause rattling or loose parts.
• Provides a secure, threaded connection for metal-to-metal or tapped-hole repairs.
• Matches OEM thread and length to maintain proper fit and alignment.

• Disconnect power and unplug the appliance before servicing.
• Use the correct hex driver or socket to avoid rounding the head.
• Thread into matching 5/16-24 tapped holes; do not force into incorrect thread sizes.
• Tighten snugly but avoid over-torquing to prevent stripping the tapped hole.

This control panel assembly replaces the oven's front user interface so you can select functions, set temperatures and start cycles from the console. Restores tactile buttons and display response for normal operation. What it does:

• Houses the oven's touchpads/buttons and display used to select cooking modes and timers
• Transmits user commands to the range control so selected functions start correctly
• Commonly replaced when buttons are unresponsive, display segments fail, or the panel is cracked
• Works with the existing control electronics and wiring harness when compatible

• One control panel assembly as shown

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the panel carefully to avoid scratching the display or bending mounting tabs
• Some models require removing the oven door or inner trim for access; refer to your service manual

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This dual harness connector is a direct-fit replacement plug that secures two wire harnesses to restore a reliable electrical connection. It helps eliminate loose or intermittent wiring connections for affected appliance circuits. What it does:

• Provides a secure, snap-fit connection between two wire harnesses
• Restores continuity to circuits that show intermittent power, no power, or erratic operation
• Holds wiring in proper alignment to prevent accidental disconnection
• Used where a dual-wire plug mates to a control, switch, or component

• One dual harness connector

• Always disconnect power to the appliance before servicing
• Inspect wire ends and terminals for damage; replace or repair wiring if needed
• Use appropriate tools to seat the connector fully; do not force or bend terminals

This left backsplash support is the metal bracket that secures the range/oven backsplash and helps keep the control panel and rear trim stable. It restores proper alignment and reduces movement of the upper back assembly. What it does

• Provides structural support for the left side of the backsplash and control panel area
• Keeps the backsplash and rear trim aligned to prevent wobble or sagging
• Helps stop vibration or rattling coming from the upper rear of the appliance
• Replaces a bent, broken, or missing left support bracket

• One left backsplash support bracket

• Disconnect power to the appliance before starting any repair
• You may need to remove the range top, control panel, or rear access panel to access mounting screws
• Use basic hand tools; keep fasteners for reuse and note their original locations
• If you see additional damaged or missing fasteners or trim, replace them as needed for a secure fit

This 8-18 x 5/8 screw fastens appliance panels and components for a secure, vibration-resistant fit. Stainless construction resists corrosion for durable long-term holding in interior appliance assemblies. What it does:

• Secures control panels, brackets, trim, and other sheet-metal parts
• Designed for 8-18 threads to match mating threaded inserts or nuts
• Square-recess (TSQ) head accepts matching driver for positive engagement
• Replaces missing, stripped, or corroded mounting screws that cause rattle or loosened parts

• One 8-18 x 5/8 screw

• Use the correct square-head driver to avoid cam-out and head damage
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow all safety precautions before working on the appliance
• Keep spare screws on hand when removing panels to prevent loss