Jb700s N1ss Parts

This gasket seals the convection fan area to help maintain proper oven airflow and temperature distribution. It replaces a worn or damaged seal to reduce air leaks and improve cooking consistency in convection ovens. What it does:

• Seals the convection fan housing to prevent heat and air leakage
• Helps maintain even oven temperatures for more consistent cooking
• Can reduce hot spots and improve convection cooking performance
• Limits airflow-related noise and vibration when properly installed

• One convection fan gasket

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and remove racks or panels as needed to access the fan housing
• Verify correct positioning and full seating of the gasket before reassembling panels

This faceplate graphics overlay replaces the printed control-panel markings so buttons and settings are readable and the range or oven looks factory-fresh. It restores clear labels for safe, accurate operation. What it does:

• Provides printed markings for the appliance control panel so temperatures, modes and buttons are legible
• Helps resolve faded, scratched or worn graphics that make controls hard to read
• Keeps the control area looking clean and factory-original
• Works with the existing control assembly — does not include buttons or electronics

• Disconnect power to the appliance before starting any work
• Remove the control panel or trim per OEM instructions to access the old graphics
• Peel off the old overlay and clean the surface thoroughly before installing the new graphics
• Align carefully and press firmly to ensure full adhesion and correct button alignment

The control panel End Plate (Left) is an OEM part for GE electric ranges. It forms a barrier along the back left edge of the control panel area providing structural reinforcement and protection.

Over time, end plates can sustain damage due to normal wear and tear of using range buttons/dials daily as well as impacts from accidental bumps. Causes may include operation fatigue plus occasional mishandling.   

Causes of a bad end plate include:

• Dents, scratches or cracks in the protective barrier surface
• Loosened mounting fasteners holding it securely  
• Reduced control panel integrity and rigidity over long use
• Exposure of fragile internal electronics to potential damage

This exact GE replacement part also fits Hotpoint, RCA and select Kenmore models.

This 14 AWG green lead wire provides a replacement grounding/conductor wire for compatible appliances, restoring secure electrical connections and reducing risk of poor contact or intermittent power. Designed to match OEM wiring size and color. What it does:

• Carries ground/ circuit connection for electrical components where a 14 AWG green conductor is required
• Restores a broken, burnt, or corroded wire that can cause intermittent operation or arcing
• Provides correct wire gauge and color coding for safe, code-consistent repairs
• Helps re-establish a firm terminal connection when original insulation or conductor is damaged

• One 14 AWG green lead wire (single wire as shown)

• Always disconnect power at the breaker or unplug the appliance before beginning work
• Route and secure the wire away from heat and moving parts; tighten terminals to manufacturer torque specs if provided

This control panel bracket secures the console assembly to the appliance, keeping the control panel aligned and stable for reliable operation. It replaces a broken or bent bracket to restore proper panel fit and reduce vibration. What it does:

• Physically supports and fastens the control/console panel to the appliance frame
• Keeps the panel aligned so buttons, knobs, and displays operate correctly
• Prevents panel wobble, rattling, or sagging that can interfere with controls
• Restores secure mounting after impact or metal fatigue

• Disconnect power to the appliance before starting work to avoid shock or injury
• Basic hand tools (screwdriver, nut driver) are usually required; remove any trim or back panels as needed
• Retain original screws and mounting hardware unless replacement hardware is specified
• If plastic clips or adjacent parts are damaged, inspect and replace them to ensure a secure fit

This oven insulation blanket fits behind the oven cavity liner to help retain heat, improve cooking performance, and reduce heat transfer to the outer cabinet. It's a direct-replacement insulating layer for affected ranges. What it does:

• Replaces worn or damaged insulation that can allow heat loss or uneven cooking
• Helps maintain proper oven temperature by reducing heat escape from the cavity
• Lowers exterior panel temperatures by providing thermal barrier
• Reduces stress on oven components caused by excessive heat exposure

• Disconnect power to the appliance and allow the oven to fully cool before beginning
• Remove oven door and/or access panels as required to reach the cavity; follow factory service instructions
• Handle insulation carefully; avoid compressing or tearing the material during installation

This oven wrapper insulation is the cavity wrap that helps contain oven heat for more consistent cooking and reduces heat transfer to surrounding cabinetry and panels. It's a simple replacement for worn, torn, or missing insulation. What it does

• Wraps the oven cavity to help hold heat in the cooking chamber
• Helps reduce heat transfer to exterior panels and nearby cabinetry
• Can improve temperature stability when old insulation is compressed or damaged
• Reduces drafts and hot spots caused by gaps or deteriorated wrap

• One oven wrapper insulation

• Always disconnect power (and gas if applicable) before servicing the oven
• Allow the oven to cool completely; remove oven panels to access the cavity
• Handle insulation with gloves and eye protection; avoid inhaling fibers if damaged
• Follow OEM instructions for placement and fasteners; do not compress insulation—install it to sit naturally around the cavity

This oven back insulation replaces the rear insulation panel to help contain oven heat and protect surrounding components — supporting consistent cooking temperatures and reducing heat transfer to the cabinet. Fits as the factory replacement panel. What it does:

• Provides thermal barrier between the oven cavity and rear cabinet, helping maintain set temperatures.
• Helps protect wiring, controls and surrounding components from excess heat.
• Can reduce external cabinet heating and help prevent heat-related discoloration or damage.
• Commonly replaced when insulation is damaged, burned, or missing after service.

• One oven back insulation panel

• Disconnect power (and gas supply if applicable) before beginning any service.
• Handle with gloves; avoid compressing or tearing the insulation material during installation.
• Removal typically requires accessing the oven rear or removing the range from its opening — follow your model's service instructions.
• Use the exact replacement part and secure per OEM fasteners and procedures.