Jb8505t1ss Parts

This oven rack is the removable wire shelf that supports pans and dishes inside your oven. Replace a bent, worn, or missing rack to restore safe, level support and proper positioning for consistent baking, roasting, and broiling.

• Provides a stable, level surface for cookware in the oven cavity
• Slides on the side rails to let you set the desired cooking height
• Helps position food at the correct distance from heating elements
• Replace if the old rack is bent, warped, corroded, missing stops, or no longer slides smoothly

What's included: 1 oven rack Installation notes:

• Allow the oven to cool completely; disconnect power or shut off gas before servicing
• Pull the old rack forward to the stops, lift the front edge, and remove
• Insert the new rack with the stop end toward the back; seat it on both side supports
• Verify the rack is level and slides securely before use

A small replacement cable clip that secures an appliance wiring harness to the cabinet or chassis, helping prevent wire rubbing and vibration. Replacing a broken clip keeps wiring routed and reduces loose, rattling wires. What it does:

• Secures wiring harnesses to the cabinet or chassis to keep wires in place and routed away from moving parts.
• Reduces wire chafing and abrasion that can cause exposed conductors or intermittent connections.
• Helps eliminate rattling noise caused by loose or vibrating wires.
• Keeps harnesses positioned to reduce stress on connectors and wiring runs.

• Always unplug the appliance or shut off power at the breaker before inspecting or replacing wiring hardware.
• Remove the old clip and press the replacement into the same mounting slot or stud until it snaps into place; light tool assistance (small flat screwdriver) can help in tight locations.
• Inspect nearby wiring and connector insulation for damage; repair or replace any frayed wires rather than relying on the clip alone.

This replacement control knob restores a worn or broken dial so you can set cooktop or oven controls precisely. It matches the OEM shape and grips the control shaft for reliable turning and selection. What it does:

• Replaces a cracked, stripped, or missing control knob to restore manual control
• Provides a secure fit on the control shaft so settings stay where you set them
• Restores tactile feedback for accurate temperature or burner selection
• Helps eliminate slipping or looseness that prevents proper function

• Remove power to the appliance before servicing (unplug or switch off circuit breaker)
• Pull the old knob straight off the control shaft; press the new knob onto the shaft until fully seated
• If the knob will not engage, verify shaft type and orientation before forcing

This genuine replacement door handle restores a secure, easy-to-grip opening for refrigerators and freezers, refreshing the appliance's appearance and usability. Designed to match OEM fit and finish for a factory look. What it does:

• Replaces a cracked, broken, loose, or missing door handle
• Provides a secure grip for opening and closing the door
• Restores proper alignment and appearance of the appliance front
• Helps prevent further damage from using a compromised handle

• Basic hand tools required; handle typically mounts with screws or clips behind the door liner
• Remove food and shelves from the door area as needed for access
• Tighten fasteners securely but avoid overtightening to prevent cracking

A replacement plastic PCB standoff that secures and insulates the appliance control board from the chassis to prevent shorts and maintain stable mounting. Restores correct spacing and support for a loose or rattling control board. What it does:

• Holds the printed circuit board off the metal frame to prevent electrical contact and shorting
• Keeps the control board aligned and stable to reduce vibration-related faults or intermittent connections
• Provides an insulated mounting point where an original standoff is cracked, missing, or worn
• Helps ensure reliable screw placement and consistent board spacing during reassembly

• One plastic PCB standoff

• Disconnect power to the appliance before servicing to avoid shock or damage
• Use the original screw size and do not overtighten to prevent cracking the standoff or PCB
• Replace any damaged mounting hardware; verify the board sits flat and is properly insulated from metal parts

Color: Stainless