Jb860sj4ss Parts

This top trim assembly replaces the finished edge piece that fits along the front of the cooktop, restoring a clean, finished appearance and covering the gap between the cooktop and control panel. It helps prevent debris from falling into internal areas. What it does:

• Covers and protects the front edge of the cooktop, improving appearance
• Hides gaps where food and spills can collect, making cleaning easier
• Helps maintain proper spacing and alignment of the cooktop edge
• Common fix for bent, dented, or cosmetically damaged top trim

• One top trim assembly

• Disconnect power to the appliance before beginning any work to avoid shock hazard
• Remove burners, grates, or cooktop components as needed for access; parts and fasteners may vary by model
• Handle trim carefully—edges can be sharp and panels may scratch; use protective gloves

The control panel End Plate (Left) is an OEM part for GE electric ranges. It forms a barrier along the back left edge of the control panel area providing structural reinforcement and protection.

Over time, end plates can sustain damage due to normal wear and tear of using range buttons/dials daily as well as impacts from accidental bumps. Causes may include operation fatigue plus occasional mishandling.   

Causes of a bad end plate include:

• Dents, scratches or cracks in the protective barrier surface
• Loosened mounting fasteners holding it securely  
• Reduced control panel integrity and rigidity over long use
• Exposure of fragile internal electronics to potential damage

This exact GE replacement part also fits Hotpoint, RCA and select Kenmore models.

This latch & harness assembly secures the appliance door and provides the electrical connection for the door latch/interlock. It restores reliable door closure and the electrical signal needed for normal operation. What it does

• Physically engages the door to keep it closed during operation
• Provides the wiring and connector for the door latch/interlock circuit
• Can prevent the appliance from starting when the door is not detected closed
• Common symptom: door won't latch, appliance won't start or stops mid-cycle

• One latch & harness assembly

• Disconnect power (and gas if applicable) before starting any repair
• Basic mechanical and electrical familiarity recommended; use proper tools
• Test operation and electrical connector seating before reassembling panels

This left door hinge secures and pivots a refrigerator or freezer door so it opens and closes smoothly. Replacing a worn hinge restores proper door alignment and helps the seal close evenly to maintain temperature. What it does:

• Provides the pivot point that supports the door and allows smooth opening/closing
• Restores correct door alignment to help prevent sagging or uneven gaps
• Reduces binding or scraping that can occur with worn or bent hinges
• Helps the door seal fully to reduce cool-air loss and compressor overwork

• Unplug the appliance and empty/secure the door before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use the existing screws or included hardware as specified by the OEM; tighten fasteners securely

This smoke eliminator is a charcoal-based filter designed for recirculating range and microwave venting. It helps reduce cooking odors and airborne grease particles when the appliance is used in non-vented (recirculating) mode. What it does:

• Adsorbs and reduces cooking odors and smoke in recirculating vent systems
• Helps capture particles that pass through the venting fan to keep kitchen air fresher
• Commonly replaced when strong cooking smells persist or airflow seems less effective
• Fits into the appliance's recirculating filter slot to restore odor control

• One (1) smoke eliminator charcoal filter

• Turn power to the appliance off before accessing the vent/filter area
• Remove the vent or grille per your appliance manual, replace the old filter with the new one, and reassemble
• No special tools usually required; refer to your model's instructions for exact access steps
• Replace periodically or when odor reduction becomes noticeably worse

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor that helps regulate heating or motor circuits in compatible appliances. Restores controlled switching for stable operation and consistent performance. What it does:

• Controls power delivery to heating elements or motors by switching current on and off
• Helps correct symptoms such as intermittent heating, burners or motors that won't respond, or erratic operation
• Replaces a failed or shorted SCR to restore proper control functionality
• Operates as part of the appliance's control/regulator circuitry to manage current flow safely

• Disconnect power (unplug appliance or switch off circuit breaker) before servicing
• Observe ESD precautions and avoid touching semiconductor contacts; handle by the body or mounting tab
• Verify correct replacement orientation and secure mounting; match wiring/terminal locations exactly