Jbs8895aac Parts

The Oven Door Gasket is an OEM part for GE ranges. This gasket is responsible for creating an air-tight seal between the door and the oven housing. It allows heat to be properly contained within the oven cavity during the cooking process. 

Causes of a bad gasket can include warping, cracking, or breakdown of the gasket material over repeated heating and cooling cycles. Exposure to excessive heat or impact damage is also possible. 

Symptoms of a bad gasket include:

• Inability to maintain proper oven temperatures 
• Leaks of heat, smoke, or flames from the door seal area
• Drafts or cold spots felt around the door perimeter
• Difficulty in fully latching the oven door closed

This OEM GE replacement gasket is also compatible with Hotpoint, RCA, and some Kenmore models.

This rotary switch turns with the control knob to open and close circuits that command your appliance's function. A worn or failed switch can cause a control to stop responding, work intermittently, or not hold its setting.

• Provides on/off or multi-position control for the selected function
• Restores proper response to the matching control knob
• Common failure signs include non-responsive control, intermittent operation, or inability to change settings
• Electrical parts should be handled with power disconnected

• Disconnect power before servicing; verify no voltage is present
• Note wire positions or take a photo before removal
• Transfer knob shaft orientation and mounting hardware from the original if reusable
• Do not overtighten mounting fasteners; test operation before reassembly

The Rotary Switch is an OEM part for GE electric ranges. This switch is located on the range control panel and allows selection of various oven functions such as bake, broil, and keep warm.

Causes of a bad rotary switch can be normal wear and tear over time, exposure to heat or moisture damage, or accidental impact. Replacing it before a complete failure occurs can help prevent further issues.

Symptoms of a bad rotary switch include:

• Inability to select desired oven functions
• Switch getting stuck or failing to rotate properly
• Displays not accurately reflecting selected function
• Intermittent or unreliable operation of oven

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This gasket seals the oven's convection fan assembly. By closing the gap between the fan cover and the oven cavity, it helps prevent air leaks and supports proper airflow for more even convection cooking and steadier temperatures. What it does:

• Seals the junction between the convection fan cover/housing and the oven liner
• Helps maintain correct airflow during convection operation
• Supports more consistent oven temperatures and even baking
• Replace if the seal is torn, frayed, compressed, or missing

• 1 convection fan gasket

• Disconnect power and allow the oven to cool completely before servicing
• Access by removing the interior convection fan cover; note gasket orientation
• Clean mating surfaces before installing; seat gasket evenly and reassemble
• Use care around sharp edges; wear cut-resistant gloves and eye protection

This oven control and faceplate is the user interface assembly that houses the oven controls and display, restoring a readable display and functional buttons for accurate oven operation. Fits the OEM form and mounting. What it does:

• Replaces the front control panel and faceplate that holds the touchpad/buttons and display.
• Restores unresponsive or damaged buttons, a cracked or faded faceplate, or a non-visible display area.
• Provides the mounting and bezel for the oven's control electronics and user controls.
• Helps return normal control access so timers, modes, and temperature settings can be entered.

• Disconnect power at the breaker before any service to avoid electrical shock.
• Handle glass and painted surfaces carefully to avoid scratches or breakage.
• Basic disassembly of the oven control housing and possibly the back guard is usually required; keep fasteners organized.

This Oven Door Gasket forms a heat-resistant seal between the oven door and the front frame. Replacing a worn seal helps your oven preheat efficiently, hold temperature more consistently, and keep heat and spills contained.

• Creates a perimeter seal to retain heat and support even baking
• Helps reduce long preheat times and noticeable temperature swings
• Replace if the gasket is torn, frayed, hardened, flattened, or leaking heat around the door
• Restores proper door closure feel and uniform contact

• Disconnect power and allow the oven to cool completely before servicing.
• Open the door and remove the old gasket by releasing it from its existing mounting points.
• Install the new gasket into the same points without stretching; ensure an even seal around the full perimeter before use.

Color: Stainless Steel

The Handle is an OEM part for GE ranges. It is the outer handle used to open and close the oven door. The handle plays an important role in providing an easy grip to safely access the oven interior.

Causes of a bad handle could include damage over time due to repeated use, chemical exposure from spills or cleaners, or loss of integrity from excessive heat.

Symptoms of a bad handle include:

• Loose fit or sensation when opening/closing the oven door
• Visible cracks, chips, or discoloration of the handle material
• Difficulty gripping or lifting the handle
• Potential safety issues if the handle breaks off unexpectedly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This handle and end cap assembly replaces a worn or damaged refrigerator door handle end for a clean, finished appearance and secure grip. Restores proper handle alignment and lets the door open and close smoothly. What it does:

• Replaces a damaged or cracked handle end cap and attached handle section
• Restores a secure grip and proper door operation
• Improves door appearance by replacing scratched or dented stainless pieces
• Helps eliminate looseness, wobble, or misalignment at the handle end

• One handle and end cap assembly (stainless), as shown

• Disconnect power or follow appliance safety procedures before starting work
• Typical installation uses basic hand tools; handle attaches to door with screws/fasteners
• Align assembly carefully and tighten fasteners snugly—do not overtighten to avoid stripping

The Element Radiant 6 Warmer is an OEM component specifically designed for GE electric ranges. This element plays an important role in warming plates and keeping cooked foods hot until serving. 

Symptoms of a bad radiant warmer element include:

• Inability to maintain an elevated temperature on the warmer oven surface 
• Fluctuating or uncontrolled warming temperatures
• Burning or scorching of foods left on the warmer for extended periods

Causes of failure can be cracking or breakage of the heating coils over time, insulation damage allowing shorts or arcing, or issues with the electronic temperature controls. 

This OEM GE replacement element is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Lamp Halogen Assembly is an OEM part for GE ranges. It is the internal light bulb that illuminates the oven cavity.

Symptoms of a bad lamp halogen assembly include:

• Dim or flickering oven light
• Stuck-on or unresponsive oven light functionality  
• Burned out or blackened bulb

Causes can be normal life cycle burnout after extended use or damage from excess vibration.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. U

The Badge Assembly is an OEM part for GE ranges. It includes the magnetic decorative badge affixed to the front of the range. This badge displays important information such as the brand name, model number, and technical specifications.

Causes of a bad badge assembly can include damage from impacts or abrasions over time, adhesive failure from repeated heat exposure, or normal wear from routine cleaning. On a range, the badge must withstand higher cooking temperatures.

Symptoms of a bad badge assembly include:

• Faded or illegible print on the badge face
• Cracks or breaks in the plastic material
• The badge lifting or peeling away from the surface
• Missing or loose attachment clips/fasteners

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Oven Control Board and Faceplate Overlay is an OEM part for GE ranges. This assembly houses both the control electronics and digital interface overlay.

Causes can include moisture damage over time, unexpected power surges, or failure from heavy daily use. Addressing issues promptly avoids more extensive future repairs.

Symptoms of a bad control assembly include:

• Fault codes displayed and controls unresponsive
• Bake and broil temperatures inaccurate or unstable
• Lights and convection fan permanently running
• Clean and timer modes inaccessible

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This 80-watt warming element provides low, steady heat to keep cooked food warm in compatible built-in warming drawers and ovens. It restores the unit's warming function so dishes stay at serving temperature between cooking and serving. What it does:

• Heats gently to maintain food temperature after cooking
• Replaces a burned-out or weak warming element that won't keep food warm
• Helps eliminate cold spots in the warming drawer or oven warming compartment
• Works as the low-heat source for timed or manual warming settings

• One 80W warming element

• Disconnect power to the appliance before attempting any service
• Handle element carefully to avoid kinking or damaging terminals
• For most installs you'll remove the warming drawer or access panel; follow OEM instructions

This Hub Blade Assembly replaces a worn or damaged blade hub to restore proper blade mounting and rotation. It secures the blade to the motor/hub so the appliance can circulate air or move contents as intended. What it does:

• Replaces the hub that holds and centers the blade, maintaining secure blade attachment
• Restores smooth rotation and reduces wobble or vibration from a loose or broken hub
• Helps stop rattling, uneven operation, or reduced airflow caused by a damaged hub
• Works as the direct mounting point between the motor/hub shaft and the blade

• One hub blade assembly

• Disconnect power before attempting any repair to avoid shock or injury
• Handle sharp blade edges carefully; use gloves and proper tools when removing/installing
• Inspect the motor shaft and fasteners for wear; replace any damaged hardware

This pilot indicator light mounts in the control panel and illuminates to show when a heating circuit is active. Replace a failed or damaged pilot light to restore a clear "on" reminder and improve everyday visibility around hot surfaces.

• Provides a visual "ON" signal when the corresponding control is turned on
• Common symptoms: indicator won't light, is dim or flickers, or the lens/housing is damaged
• Restores a clear status cue to help you see when heat is active
• Direct replacement for the original pilot light assembly

• Disconnect power at the breaker before servicing
• Remove back cover or control panel trim to access the light
• Note wire positions and transfer them to the new light one at a time
• Seat the light securely in the panel opening, reassemble, and test

The Terminal Block Assembly is an OEM part for GE electric ranges. It provides connections between internal wiring and the home's electrical supply.

Causes of failure can include corrosion of metal prongs from heat and moisture exposure over time, splitting insulation sheathing from continuous vibrations, or loosened mounting fasteners.

Symptoms of a faulty terminal block include:

• Intermittent or unstable power to heating elements surfaces 
• Loose, frayed, or corroded wire attachments risking electrical faults
• Inability to maintain programmed cooking temperatures

This part is also compatible with Hotpoint and RCA electric range models.